background image

 10

 

 

 

Door for change 
gear compartment

Protective cover, enclosing the motor pulley, the drive pulley and drive 
belt and the change gears. The gear cover operates an interlock 
microswitch that will prevent the motor being started if the cover is not 
closed. 
 

Oil drain plug 

The oil drain plug is a hex head bolt with a sealing washer located low 
down at the rear of the headstock gear box, - when refitting the oil 
drain plug ensure that the mating faces of the headstock and the 
sealing washer are clean. 

Headstock cover 
plate 

The headstock cover plate is a flat metal plate secured to the top of 
the headstock gearbox by four cap head bolts. Unscrew the bolts and 
remove the cover to inspect the gearbox or replace or top up the oil. 
There is no gasket beneath the cover plate, so ensure the mating 
surfaces are clean before replacing the cover. 
 

18T reversing 

The 18T reverse tumbler gear, when fitted, enables the rotation of the 
leadscrew to be reversed, For left hand threads (as Fig 6) or in the 
case of an asymmetric change gear selection to allow the leadscrew 
to maintain its correct rotation (as Fig 7). 
Fig 11 shows the reverse tumbler gear fitted in the gear train. 
 

Oil sight glass 

The oil level sight glass enables you to check the amount of oil you 
have in your lathe. 

 

Fig 6                                                          Fig 7 

       

18T reversing gear (left hand thread) 

 

                                                                   

63T                                                                        63T 

 

 

 

                                                                   

60T 

 

                                                                  40T                                                                        40T 

 

                                                                  18T                                                                        18T 

 

 

                                                                    40T                                                                      40T 

 

 

 

 

 

 

 

Identification and Description of the parts   

       

Содержание BV20BL















Отзывы: