manualshive.com logo in svg

Mab Robotics MD80 x CANdle, Руководство пользователя

Поделиться
Скачать
Mab Robotics MD80 x CANdle Скачать руководство пользователя страница 24

Note: this setting has to be saved to be preserved a er power down! Please see the config save <ID>

command.

mdtool config save command <ID>

For the config commands to take action a er the next power cycle a save command has to be executed. This
command saves the current driveʼs settings to the non-volatile FLASH memory.

mdtool setup calibration command <ID> <torque bandwidth>

The calibration is always performed in the factory, however, if for some reason youʼd like to rerun it the
calibration command can be used to do just that. During calibration, the drive has to be able to rotate freely

and the power supply should be able to deliver at least 1A of current. For more detail on the calibration
process please refer to the

calibration

section.

mdtool setup diagnostic command <ID>

This command returns basic diagnostic information:

●

Driveʼs ID

●

Current CAN speed

●

Current Position

●

Current Velocity

●

Current torque

●

Current temperature (0* if the thermistor is not mounted)

●

Errors

Reading the errors is the easiest way of debugging possible problems with the drive.

Error code

Description

ERROR_BRIDGE_OCP

Overcurrent was detected by the MOSFET driver

ERROR_BRIDGE_FAULT

A general fault of the MOSFET driver

ERROR_OUT_ENCODER_E

Output encoder general error

ERROR_OUT_ENCODER_COM_E

Output encoder communication error

ERROR_PARAM_IDENT

Error during calibration of the drive, during the resistance and

inductance measurements

ERROR_UNDERVOLTAGE

Under voltage detected

ERROR_OVERVOLTAGE

Overvoltage detected

ERROR_TEMP_W

Overheat warning

ERROR_TEMP_SD

Overheat shutdown

ERROR_CALIBRATION

A general error during calibration

ERROR_OCD

Overcurrent detected

ERROR_CAN_WD

CAN watchdog triggered

mdtool blink command <ID>

This command is mostly used to find an MD80 drive on a long CAN bus using its ID – the command makes the
drive flash its onboard LEDs for easy identification.

mdtool test command <ID> <position>

This command is used to test the actuator movement in impedance mode. It helps to assess if the calibration

was successful and if there are no issues visible to the naked eye. The position argument is always the
amount of position for the motor to be moved from the current position.

www.mabrobotics.pl

[email protected]

Содержание MD80 x CANdle




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды