RPPD
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: [email protected]
EM-1693 Rev.11 P. 5 / 7
HARDWARE SETTING & CALIBRATION
Sensitivity Adj. (V
H
)
Sensitivity Adj. (V
L
)
Sensor Excitation Adj.
O
N
2
1
3
4
5
6
7
8
Set each switch referring
to the table below.
O
N
2
1
3
4
5
6
7
8
SW2
SW1
Set each switch referring
to the table below.
(front cover open)
Input Monitor LED PL1
Input Monitor LED PL2
There is no need of hardware adjustment for RS-422 line driver pulse input.
Unnecessary switches or LEDs are not provided.
■
SW1 & 2 FUNCTIONS (SW1: Input 2, SW2: Input 1, SW1-3 and SW2-3 are used commonly to both inputs.)
SWITCH
NO.
INPUT CODE
SW FUNCTION
A
B
C
D
H
SW1,2 - 1 ON with dry contact input (model suffix: A)
ON
OFF
OFF
OFF
OFF
2 ON with 2-wire current pulse input (model suffix: H)
OFF
OFF
OFF
OFF
ON
3 SW1-3: Adjustable range of sensitivity level for V
L
(ON: 0 – 10 V, OFF: 0 – 5 V)
SW2-3: Adjustable range of sensitivity level for V
L
(ON: 0 – 10 V, OFF: 0 – 5 V)
Refer to the section “SENSITIVITY ADJUSTMENT”.
ON or OFF
(required level)
OFF
ON or
OFF
(required
level)
OFF
4 Always ON
ON or OFF according to the adjustment
5 Noise filter Type 1 (ON: with, OFF: without)
ON or OFF according to the noise level.
Refer to the tables below for the max.
frequency which can pass through the filter.
6 Noise filter Type 2 (ON: with, OFF: without)
7 Attenuator for input signal (ON: with, OFF: without)
Input voltage is attenuated to half the original amplitude with this switch ON.
(one-third for the model number suffix code A.)
OFF*
OFF*
OFF
OFF*
OFF
8 Input pulse sensing method (ON: DC coupled, OFF: AC coupled)
Turn this switch off with a 10 V or greater offset.
ON
*Set to ON with excitation voltage ≥ 24 V.
■
INPUT FILTER
The tables below show the maximum frequency which can pass through the filter when the sensitivity level is set to 2 V. The
frequency may change according to the sensitivity level.
After turning the filter ON, check that the PL1 and PL2 blink according to the input signals. If they do not, readjust the
sensitivity according to the instructions in the following section.
• Noise Filter Type 1 (SW1/2-5 = ON)
DC Coupling
(SW1/2-8 = ON)
AC Coupling
(SW1/2-8 = OFF)
V p-p (V)
MAX. FREQ. (Hz)
V p-p (V)
MAX. FREQ. (Hz)
5
69
5
22
12
35
12
65
24
89
24
112
• Noise Filter Type 2 (SW1/2-6 = ON)
DC Coupling
(SW1/2-8 = ON)
AC Coupling
(SW1/2-8 = OFF)
V p-p (V)
MAX. FREQ. (Hz)
V p-p (V)
MAX. FREQ. (Hz)
5
1220
5
256
12
329
12
664
24
851
24
1090