M-system R7C-YS4, Инструкция по эксплуатации, Страница: 2 / 9

R7C-YS4
EM-7801-AE P. 2 / 9
COMPONENT IDENTIFICATION
5
4
3
2 1 0 9
8
7
6 5
4
3
2 1 0 9
8
7
6 5
4
3
2 1 0 9
8
7
6
ERR RD
RUN SD
PWR
X10 X1
STATION ADD. B.RATE
CNFG.
1 2 3 4 5 6 7 8
4 5 6 7
1 2 3 2 3 4 1 5
10 7 8 9 6
(A) Status Indicator LED
*
1
(B) Station Address Setting Rotary SW
(C) Baud Rate Setting Rotary SW
(D) Operating Mode Setting DIP SW (SW1)
(E) PC Configurator Jack
(F) CC-Link, Power Supply Terminals
(G) Output Terminals
(H) Terminating Resistor SW
* 1. Refer to ‘Status Indicator LED’ section for detailed information.
(A)
(F) (G)
(B) (C) (D) (E)
TERM
ON
OFF
■
SIDE VIEW
■
FRONT VIEW
(H)
■
STATUS INDICATOR LED
ID COLOR FUNCTION
PWR Red Turns on when the internal 5V is sup-
plied normally.
RUN Red Turns on when the refresh data is re-
ceived normally.
ERR Red Turns on when the received data is
abnormal.
SD Red Turns on when the module is transmit-
ting.
RD Red Turns on when the module is receiving.
■
STATION ADDRESS
Station Address is selected between 1 and 64 in decimal.
The left switch determines the tenth place digit, while the
right switch does the ones place digit of the address.
5
4
3
2
1 0
9
8
7
6
5
4
3
2
1 0
9
8
7
6
Station Address Setting (x1)
Station Address Setting (x10)
■
BAUD RATE
Baud Rate is selected with the rotary switch.
5
4
3
2
1 0
9
8
7
6
Baud Rate Setting
0 : 156 kbps
1 : 625 kbps
2 : 2.5 Mbps
3 : 5 Mbps
4 : 10 Mbps
■
OPERATING MODE
(*) Factory setting
• Output at the loss of communication (SW1-4)
SW1-4 OUTPUT AT THE LOSS OF COMMUNICATION
OFF Reset the output (to -15%)
ON
Hold the output (*)
(maintains the last data received normally)
Note : Be sure to set unused SW1-1 through 1-3 and 1-5
through 1-8 to OFF.
■
POWER SUPPLY, CC-LINK TERMINAL ASSIGNMENT
4
DA
5
DG
6
U(+)
1
DB
2
SLD
3
FG
7
V(–)
NO. ID FUNCTION, NOTES
1 DB White
2 SLD Shield
3 FG FG
4 DA Blue
5 DG Yellow
6 U(+) Power input
7 V(–) Power input
■
OUTPUT TERMINAL ASSIGNMENT
6
NC
7
I0
8
I1
1
NC
2
COM0
3
COM1
9
I2
4
COM2
10
I3
5
COM3
NO. ID FUNCTION NO. ID FUNCTION
1 NC No connection 6 NC No connection
2 COM0 Common 0 7 I0 Current output 0
3 COM1 Common 1 8 I1 Current output 1
4 COM2 Common 2 9 I2 Current output 2
5 COM3 Common 3 10 I3 Current output 3
■
TERMINATING RESISTOR
To use the terminating resistor, turn the switch ON, and
OFF to invalidate. (Factory setting OFF)
056 222 38 18 mailbox@sentronic.com www.sentronic.com
SENTRONIC
AG