manualshive.com logo in svg

M-system M3-UNIT Series, Руководство по эксплуатации, Страница: 35 / 40

Поделиться
Скачать
M-system M3-UNIT Series Скачать руководство пользователя страница 35

35

M3LDY OPERATING MANUAL EM-2664-B Rev.0

12.  APPENDICEs

12.1  sPECIFICATIONs

12.1.1  GENERAL sPECIFICATIONs

Construction

Small-sized front terminal structure

Connection

Euro type connector terminal

Housing material

Flame-resistant resin (gray)

Isolation

Input to output to power

Overrange output

-15 to +115%

Zero adjustment

-15 to +15% (front)

Span adjustment

85 to 115% (front)

Status indicator LED

Tri-color (green/amber/red) LED; Blinking patterns indicate operation status of the
transmitter.

Configuration

DIP SW configuration

Input type, output type, front control button lock, configuration mode

PC configuration

Refer to 12.2 PC CONFIGURATOR SOFTWARE.

Calibration

I/O ranging and fine adjustment via ‘One-Step Cal’ calibration or PC

Configurator connection

2.5 dia. miniature jack; RS-232-C level

12.1.2  sUPPLY OUTPUT

SUPPLY OUTPUT (across the terminals 1 – 2)

Output voltage

24 – 28 V DC with no load
19 V DC minimum at 20 mA

Current rating

≤ 22 mA DC

Permissible load resist-
ance

LR (Ω) ≤ (19 – Min. Operational Voltage) V ÷ 0.02 A

Shortcircuit Protection

Current limited

35 mA max.

Protected time duration

No limit

12.1.3  INPUT sPECIFICATIONs

DC Current

Input resistance:  274.9 Ω resistor incorporated (24.9 Ω when used as isolator)
Maximum range:  0 – 20 mA DC
Minimum span:  2 mA
Offset:  Lower range can be any specific value within the input range provided that 
the minimum span is maintained.

12.1.4  OUTPUT sPECIFICATIONs

Output types and ranges are shown in the following table.

DC Current

Maximum range:  0 – 20 mA DC
Minimum span:  1 mA
Conformance range:  0 – 24 mA DC
(Negative overrange current below 0 mA is not available.)
Offset:  Lower range can be any specific value within the output range provided 
that the minimum span is maintained.
Load resistance:  Output drive 12 V maximum

DC Voltage

Narrow spans
  Maximum range:  -2.5 – +2.5 V DC
  Minimum span:  250 mV
  Conformance range:  -3 – +3 V DC
Wide spans
  Maximum range:  -10 – +10 V DC
  Minimum span:  1 V
  Conformance range:  -11.5 – +11.5 V DC
Offset:  Lower range can be any specific value within the output range provided 
that the minimum span is maintained.
Load resistance:  Output drive 1 mA maximum

Содержание M3-UNIT Series









































Отзывы:

Нет отзывов