ASD1
P. 1 / 3
EM-1610 Rev.2
BEFORE USE ....
Thank you for choosing M-System. Before use, check the
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■
PACKAGE INCLUDES:
Signal conditioner (body + base input resistor) ... (1)
Input resistor is provided only with current input type.
■
MODEL NO.
Check that model No. described on the specification label is
exactly what you ordered.
■
INSTRUCTION MANUAL
This manual describes necessary points of caution when you
use this product, including installation, connection and basic
maintenance procedures.
POINTS OF CAUTION
■
CONFORMITY WITH CE/LVD DIRECTIVE OR UL
(CE/UL is unavailable for certain model suffix options.)
•␣ This equipment is suitable for use in a Pollution Degree 2
environment and in Installation Category II, with the maxi-
mum operating voltage of 300V.
Basic insulation is maintained between the input, output and
power. Prior to installation, check that the insulation class
of this unit satisfies the system requirements.
• The equipment must be mounted inside a panel.
• The equipment must be installed such that appropriate
clearance and creepage distances are maintained to conform
to CE/UL requirements. Failure to observe these require-
ments may invalidate the CE/UL conformance.
■
POWER INPUT RATINGS
• Check the power rating for the unit on the specification label.
Rating 100 – 120V AC: 90 – 132V, 47 –␣ 66 Hz, approx. 3VA
Rating 200 – 240V AC: 180 – 132V, 47 –␣ 66 Hz, approx. 3VA
■
UNPLUGGING THE UNIT
• Before you remove the unit from its base socket or mount it,
turn off the power supply and input signal for safety.
■
ENVIRONMENT
• Indoor use
• When heavy dust or metal particles are present in the air,
install the unit inside proper housing with sufficient ventila-
tion.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -5 to +60
°
C (23
to 140
°
F) with relative humidity within 30 to 90% RH in order
to ensure adequate life span and operation.
■
WIRING
• Do not install cables (power supply, input and output) close
to noise sources (relay drive cable, high frequency line, etc.).
• Do not bind these cables together with those in which noises
are present. Do not install them in the same duct.
INSTRUCTION MANUAL
MODEL
ASD1
DC ALARM
(thumbwheel switch adjustment)
Input Resistor
■
AND ....
• The unit is designed to function as soon as power is
supplied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data sheet.
COMPONENT IDENTIFICATION
■
FRONT PANEL CONFIGURATION
INSTALLATION
Detach the yellow clamps located at the top and bottom of the
unit to separate the body from the base socket.
■
DIN RAIL MOUNTING
Set the base socket so that its
DIN rail adaptor is at the bot-
tom. Position the upper hook
at the rear side of base socket
on the DIN rail and push in the
lower. When removing the
socket, push down the DIN rail
adaptor utilizing a minus
screwdriver and pull.
■
WALL MOUNTING
Refer to the drawings in the
following page.
SET2
3
SET1
1
4 4
12
3
4
5
6
7 8 9
0
12
3
4
5
6
7 8 9
0
Model
ASD1
Body
Specification
Label
Base Socket
Clamp
(top & bottom)
DIN Rail
35mm wide
Spring Loaded
DIN Rail Adaptor
Shape and size of the base socket
are slightly different with various
socket types.
Monitor LED
•Output 1
Setpoint Adj.
9 9
Setpoint Adj.
•Output 2
9 9
Monitor LED
Hysteresis (Deadband) Adj.
Hysteresis (Deadband) Adj.
