M-system 47DAC Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 251

background image

107

47DAC OPERATING MANUAL EM-9518-B Rev.4

9.6 OFF DELAY TIME

Alarm output is canceled when the display value returns to the value to cancel the alarm and stays for the specified time
duration, which prevents the alarm output from being canceled by a rapid or sudden change such like external disturbance.
This time duration is called OFF delay time and can be set within the range of 0.0 to 99.9 seconds.  The default value is 0.0
second.  The OFF delay time is configurable also for the P status.

NOTE

The one-shot output setting prevails the OFF delay time.

9.6.1 OPERATING PROCEDURE

NOTE

The following figures are display examples. The displays
depend on the settings.

1

Hold down Alarm/

↓

button for 3 seconds or more to move on

to Alarm Setting Mode.

• The alarm output pattern is indicated.
• The SD indicates ‘ALM PTN’.

NOTE

With the bank switching set to “enabled via the front button control”, the bank No. is indicated (‘ALM BNK’ on the SD).

2

Press Alarm/

↓

or Scale/

↑

button to go to the LL (L, H, HH or P)

OFF delay time setting.

• The LL (L, H, HH or P) OFF delay time is indicated.
• The SD indicates ‘OFDLYLL’ (‘OFDLY L’, ‘OFDLY H’, ‘OFDLYHH’ or

‘OFDLY P’).

• ‘LL’ (‘L’, ‘H’, ‘HH’ or ‘P’) indicator starts blinking.

1,2,

4

2,4

3

3

Blinking

Blinking

«
...
105
106
107
108
109
...
»

Содержание 47DAC




























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 47DAC

Бренд: Yamaha Страницы: 8

Бренд: Magnetic Instrumentation Страницы: 63

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hammond Страницы: 16

Бренд: Oldham Страницы: 34

Бренд: Xantrex Страницы: 2

Бренд: Xaoc Devices Страницы: 8

Clavinova CVP-805

Бренд: Yamaha Страницы: 112

Clavinova CLP-270

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 3

Бренд: Yamaha Страницы: 48

Бренд: ESP Страницы: 12

Бренд: Fly Henry Страницы: 5

Бренд: Supertech agroline Страницы: 10

Ocean Optics HR2000 Series

Бренд: Halma Страницы: 42

Бренд: Roland Страницы: 2

LiveTester LT 220

Бренд: StarLogixs Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды