M-E AERCOM AC-210, Руководство по эксплуатации

Страница: 13 / 36

ENGLISH | AERCOM
13
OUTDOOR STATION
The outdoor station is splash-proof in accordance with IP44 but should
not be exposed to heavy rain. Thus a somewhat protected assembly
location is advantageous.
The wire between the power box and the outdoor station is connected
with screw terminals. The wire can be disconnected from the power box
by releasing all the screw terminals. The connection terminal is marked
with the cable colours but you should still note or photograph how the
wires are connected.
1) Find a suitable location for the outdoor intercom unit.
2) Drill the mounting holes with a diameter of 6 mm using the drilling
template and also drill an 8 mm hole to insert the cables through
the wall.
CAUTION : Only drill the 8 mm hole here if you are mounting the
power box exactly opposite the outdoor intercom unit. Otherwise find
a suitable location to lay the cable and then lay it to the power box
(maximum wire length 10 m).
3) Place a dowel in each of the 6 mm holes.
4) Remove both the screws (4.5) from the outdoor station in order
to be able to lift the front casing section from the lower section
(please ensure that the wire for the loudspeaker and brightness
sensor is not ripped out).
5) Push the cable from the outdoor station through the 8 mm hole
or lay it to the power box and screw the back casing section to the
wall with four screws.
6) Adapt nameplate
1. Remove the nameplate from the front casing section (it is held
only by magnets).
2. Remove both the screws from the nameplate and open it up.
a) Remove the strip of paper and write your name on it.
You can also make a nameplate on your PC and print it out.
The dimensions of the paper strip are 15mm x 70mm.
b) Re-mount the outdoor speaker unit by repeating the steps
6.1 and 6.2 in reverse order.
7) Hang the front casing section over the back casing section and
replace the two screws (4.5).
NOTE : In order not to have to lay the wire from the outdoor speaker
unit visibly please drill the hole for the wire penetration through the
wall directly behind the outdoor speaker unit where possible (as shown
on the drilling template). This is easiest if the power box is mounted
directly opposite.
POWER BOX
The power box is only suitable for indoor assembly and is simply hung
on a screw. Drill a 6 mm hole in a suitable position of the wall, insert a
dowel and insert the screw until the head protrudes by approximately 3
mm. The power box then hangs on the screw.
If the power box is too loose, please turn the screw a little further into
the wall.
The connection cable to the outdoor station can be fed into the power
box from the back. When laying the wire please ensure that the wire
comes out of the wall at the right position behind the power box. If
the wire was laid on the plaster then the power box has a small cable
channel on the back, through which you can lead the cable into the
power box. The power box then lies flush against the wall.
CHARGING CRADLE
The charging cradle is simply hung on a screw, like the power box.
INITIAL OPERATION
Charge the mobile indoor station(s) completely before initial operation.
1. Insert the mains power supply for the charging cradle into the
socket and connect using the hollow plug on the charging cradle.
The red power LED will light up.
2. Insert the mobile Indoor station into the charging cradle, the Power
LED (1.1) will indicate the charging process by lighting red. When
the charging process is complete the LED colour will turn to green.
3. Re-connect the wire from the outdoor station to the power box if
you have detached it.
4. Plug the mains power supply for the power box into a socket and
connect the hollow plug with the socket (3.13) in the power box.
The power LED will light after a few seconds and a short tone will
sound on the outdoor station.
5. Switch the mobile indoor station on using the switch (1.3), the
reception indicator (1.11) will flash for a few seconds. Once the
connection is made the LC display will show the temperature and
the reception indicator will be constant.
The intercom is now ready for use.