background image

15

English

Studiophile

TM

 CX8   

User Guide

8.  Appendix A - Technical Specifications 

Frequency response:

38Hz-30kHz  (+/-3dB)

Crossover frequency:

2.7kHz

Low-frequency amplifier 
power:

80 watts with 14 gauge wiring to this transducer

High-frequency 
amplifier power:

40 watts with 14 gauge wiring to this transducer

LF cutoff

Flat, 60Hz, and 80Hz

MF boost

In/Out of 2dB centered at 2kHz

HF trim

+2dB, 0dB, -2dB above 3kHz

Acoustic space

0dB, -2dB, and -4dB

Maximum  
signal-to-noise 
(dynamic range):

> 97 dB (typical A-weighted)

Polarity:

positive signal at + input produce outward LF cone displacement 

Input impedance:

20k ohms balanced, 
10k ohms unbalanced 

Input sensitivity:

100 mV pink noise input produces 95 dBA output SPL at one meter with volume 
control at maximum 

Power:

factory programmed for either 115V ~50/60Hz or 230V ~50/60Hz 

Protection:

RF interference, output current limiting, over temperature,  
turn-on/off transient, subsonic filter, external mains fuse

Cabinet:

Front and rear baffle 1” MDF with ¾” MDF wrap. Black lacquer paint on enclosure 
with soft touch black paint on curved front plate. 

Size:

17” (H) x 11” (W) x 13” (D); 43.2cm x 28cm x 33cm

Weight:

30.42 lbs./unit; 13.8 kg

Above specifications subject to change without notice 

Содержание Studiophile CX8



















Отзывы: