manualshive.com logo in svg

Lycoming IO-360-N1A, Инструкция по установке и эксплуатации, Страница: 54 / 74

Поделиться
Скачать
Lycoming IO-360-N1A Скачать руководство пользователя страница 54

                      IO-360-N1A Engine Installation and Operation Manual

 

Engine Conditions

 

© 2016 Avco Corporation. All Rights Reserved

 

Page 34 

 

February 2016 

5.

 

Before take-off, monitor the oil pressure, oil temperature, and cylinder head temperature to 
make sure all are within their operating ranges (as specified in Appendix A). 

 

DO NOT TAKE-OFF IF ANY OF THE FOLLOWING CONDITIONS ARE 
FOUND: 

 

Engine roughness 

 

Low, high or surging rpm or fluctuations 

 

High, low, or fluctuating oil pressure 

 

High or low fuel flow 

 

High manifold pressure 

 

Low battery charge. 

6.

 

Make sure that when take-off power is applied smoothly, oil pressure, fuel flow, manifold 
pressure, and rpm remain stable. 

Engine Operation in Hot Weather 

1.

 

During engine operation in hot weather: 

A.

 

Monitor oil and cylinder temperatures during taxiing and engine run up. 

B.

 

Operate with cowl flaps fully open. 

C.

 

Do not operate the engine at maximum power any longer than necessary to make the 
climb configuration recommended by the aircraft manufacturer. 

D.

 

Enrich fuel mixture as necessary. 

E.

 

Operate at sustained sufficient airspeed to cool off the engine. 

F.

 

Continue to closely monitor temperatures. 

Volcanic Ash 

1.

 

Given the dynamic conditions of volcanic ash, Lycoming’s recommendation is NOT to 
operate the engine in areas where volcanic ash is present - in the air or on the ground. Refer 
to the latest revision of Service Instruction No. SI-1530 for any new details. 

2.

 

Ash on the ground and runways can cause contamination in the engine compartment and 
subsequent engine damage during aircraft landing or take-off. 

3.

 

Piston engines can be damaged by inlet air contaminated with volcanic ash. Solid deposits 
from any number of sources can collect on engine baffles or other engine surfaces and 
prevent engine cooling. Accumulation of deposits on the induction air filter can restrict or 
block air flow to the engine and significantly decrease engine power. Contamination of 
engine oil can cause engine malfunction and/or failure from abrasive wear. 

4.

 

However, if during flight, the engine is in a particulate-laden atmosphere, do the following: 

(a)

 

Monitor the engine temperature during flight. (Damaged or blocked cooling baffles or 
heavy deposits on engine cooling surfaces can decrease cooling efficiency and cause the 
engine to overheat.) 

Содержание IO-360-N1A











































































Отзывы:

Нет отзывов