LXNAV LX80xx Скачать руководство пользователя

Страница: 173 / 192

Flying with the System

Version 6.03, May 2017

Page 173 of 192

7.2.7

Graphical Final Glide assistants

There are few graphical final glide assistants available:



Glider range (outside/inside fill)



Different colours of APTs in near mode list



Different colours of APTs on the map



Square symbols

Glider range

can be filled outside or inside. Different fill type, colour and opacity can be set

at 5.1.6.4 chapter.

In Near mode arrival altitude is coloured in white, yellow and red.

White final glide shows APT in range at current MC setting.

Yellow final glide shows reachable airports if you decrease your MC to zero.

Red colour means these APTs cannot be reached.

The same colour logic is used for the APTs appearance on the map.

Yellow square

indicates final glide at MC 0. Once you reach the

green square

LX will give

you a message “Task on final glide” with current MC setting.

Содержание LX80xx

































































































































































































Результаты поиска

Содержание LX80xx

Отзывы:

Похожие инструкции для LX80xx

Бренды по названию

Популярные бренды

LXNAV LX80xx, Руководство пользователя

Результаты поиска

Содержание LX80xx

Отзывы:

Похожие инструкции для LX80xx

Бренды по названию

Популярные бренды