luxvision LM-7800 Скачать руководство пользователя

Страница: 10 / 57

------------------------------------------------------------------------- LM-7800 User Guide

2.4.

Safety Precautions

This equipment has been developed and tested according to safety standards as well as

national and international standards. This guarantees a very high degree of safety for this

device. The legislator expects us to inform the user expressively about the safety aspects

in dealing with the device. The correct handling of this equipment is imperative for its safe

operation. Therefore, please read carefully all instructions before switching on this device.

For more detailed information, please contact our Customer Service Department or one of

our authorized representatives.

This equipment

must not be used (a) in an area that is in danger of explosions

and (b) in the presence of flammable, explosive, or volatile solvent such as alcohol,

benzene or similar chemicals.

Do not put or use this device in humid rooms. Humidity should be maintained

between 50 and 80% for normal operation. Do not expose the device to water

splashes, dripping water, or sprayed water. Do not place containers containing

fluids, liquids, or gases on top of any electrical equipment or devices.

The equipment must be operated only by, or under direct supervision a

properly trained and qualified person.

Modifications of this equipment

may only be carried out by

Luxvision's

service technicians or other authorized persons.

Customer maintenance of this equipment

may only be performed as stated in

the User’s Manual and Service Manual. Any additional maintenance may only be

performed by

Luxvision's

service technicians or other authorized persons.

The manufacturer is only responsible for effects on safety, reliability, and

performance of this equipment when the following requirements are fulfilled: (1) The

electrical installation in the respective room corresponds to the specifications stated

in this manual and (2) This equipment is used, operated, and maintained according to

this manual and Service Manual.

The manufacturer is not liable for damage caused by unauthorized tampering

with the device(s). Such tampering will forfeit any rights to claim under warranty.

Содержание LM-7800


























































Результаты поиска

Содержание LM-7800

Отзывы:

Похожие инструкции для LM-7800

Бренды по названию

Популярные бренды

luxvision LM-7800, Руководство по эксплуатации

Результаты поиска

Содержание LM-7800

Отзывы:

Похожие инструкции для LM-7800

Бренды по названию

Популярные бренды