Fold
Fold
Fold
Next, connect an Ethernet cable from your Router or Switch to the
Data
IN
port on the PoE Injector. Finally, connect the AC cord to the included
PoE Injector, then to the AC outlet.
n
Note:
Luxul recommends at least Cat-5e unshielded twisted pair
(CAT5e UTP) cabling. To ensure best performance at 1000 Mbps, use
CAT6 UTP.
PoE Injector Setup
X
Data In:
Connect an Ethernet cable from your router or switch to the
Data In
port of the included PoE Injector.
X
Data & PWR Out:
Connect an Ethernet cable from the
Data & PWR Out
port of the included PoE Injector to the PoE Port of the XAP-810.
X
AC Power:
Connect the included AC Cord to the Power Input of the
Included Injector first and then to the AC outlet.
Power
Source
From your
Router or Switch
Luxul AP
DATA IN
DATA &
PWR OUT
POE
Injector
PoE injector
3
Preparing for Access
IP Addressing
If the XAP-810 is connected to a network with a 192.168.0.X address scheme,
and your computer shares a similar address on the same network, you can
skip to the next step,
Access and Setup
.
If your network uses an address scheme other than 192.168.0.X, you’ll need
to set a temporary static IP address on the computer you’re using for config-
uration. To do so, set the IP address of your computer to any address in the
192.168.0.X range other than 192.168.0.10.
Once you’re finished configuring the AP, you can return your computer’s IP
configuration to normal, typically “Obtain Automatically/DHCP.”
n
Note:
Visit
http://luxul.com/ip-addressing
to learn more about
changing your computer’s IP address and getting connected.
4
Access and Setup
Getting Connected
X
Connecting Via an Ethernet Device:
Use Ethernet cable to connect
your computer to the PoE switch or PoE injector to which the XAP-810 is
connected. Ethernet is the preferred method of connection.
X
Connecting Via a Wireless Device:
Connect your client device to the
XAP-810 default wireless network named
Luxul_XAP810
or
Luxul_
XAP810_5G
. The wireless network will run in Open Security mode, so no
passphrase is required until Wireless Security is configured.
Logging In
To access the AP’s web configuration, open your web browser and enter the
AP’s default 192.168.0.10 IP address in the address field. Log in to the AP using the
default user name and password:
Default IP: 192.168.0.10
Username: admin
Password: admin
n
Note:
If another device on your network shares the 192.168.0.10 address,
you’ll need to temporarily reassign or remove that device while
you configure the XAP-810.
n
Note:
The XAP-810 is not a router and will need to be connected to a
network with a router in order to deliver Internet access.
5
Hardware Operation
LED Indicators
Enclosure:
If the green Power LED is on, the XAP-810 is powered and working. If
the Power LED is OFF, the AP is not receiving power or the LED has been turned
off in the AP’s web interface. If the green Power LED is blinking, the XAP-810
is booting. The two blue LEDs indicate indicate each of the 2.4GHz and 5GHz
networks are configured and broadcasting.
XAP-810 LED’s
PoE Injector:
If the PWR LED is On, Power is Connected to the injector. If
the PWR LED is Off, the injector is not receiving power.
Reset Button
The Reset button is located underneath the mount and
marked RESET. It may be used to reboot the AP or to restore
factory default settings.
Reboot the AP:
With the XAP-810 powered on, simply press
and release the Reset button.
Restore Factory Defaults:
With the XAP-810 powered on, press and hold
the Reset button for 10 seconds, then release the button and the XAP-810
will restore factory defaults and reboot.
c
CAUTION:
Holding the Reset button for more than a few seconds
will restore the AP to factory default and remove any
custom configuration.
