Fold
Fold
Fold
AP SETUP AND CONFIGURATION CONT.
2
Connecting Ethernet and Power
Ethernet and Power
The XAP-1440 is PoE ready and supports 802.3at PoE. A PoE injector is
included with the device. To apply power, simply connect the end of the
Ethernet cable to which the access point is connected to the provided PoE
injector or other PoE switch. An Ethernet cable length of up to 300 feet can
be used.
n
Note:
Luxul recommends at least Cat-5e unshielded twisted pair
(CAT5e UTP) cabling. To ensure best performance and stable data
transmission at 1000 Mbps, use Category-6 unshielded twisted pair
(CAT6 UTP).
PoE Injector Setup
X
Data In:
Connect an Ethernet cable from your router or switch to the
Data In
port of the included PoE Injector
X
Data & PWR Out:
Connect an Ethernet cable from the
Data & PWR Out
port of the included PoE Injector to the PoE Port of the XAP-1440
X
AC Power:
Connect the included AC Cord to the Power Input of the
Included Injector first and then to the AC outlet.
Power
Source
From your
Router or Switch
Luxul AP
IN
OUT
POE
Injector
PoE injector
3
Preparing for Access
IP Addressing
If the XAP-1440 is connected to a network with a 192.168.0.X address scheme,
and your computer shares a similar address on the same network, you can skip
to the next step,
Access and Setup
.
n
Note:
If another device on your network shares the 192.168.0.10 address,
you’ll need to temporarily reassign or remove that device while
you configure the XAP-1440.
If your network uses an address scheme other than 192.168.0.X, you’ll need
to set a temporary static IP address on the computer you’re using for config-
uration. To do so, set the IP address of your computer to an address in the
192.168.0.X range.
Once you’re finished configuring the AP, you can return your computer’s IP
configuration to normal, typically “Obtain Automatically/DHCP.”
n
Note:
Visit
http://luxul.com/ip-addressing
to learn more about
changing your computer’s IP address and getting connected.
n
Note:
The XAP-1440 is not a router and will need to be connected to
a network with a router in order to deliver Internet access.
4
Access and Setup
Getting Connected
X
Connecting Via an Ethernet Device:
Use Ethernet cable to connect your
computer to the PoE switch or PoE injector to which the XAP-1440 is
connected. Ethernet is the preferred method of connection.
X
Connecting Via a Wireless Device:
Connect your client device to the
XAP-1440 default wireless network named
Luxul_XAP-1440
. The wireless
network will run in Open Security mode, so no passphrase is required until
Wireless Security is configured.
Logging In
To access the AP’s web configuration, open your web browser and enter the
AP’s default 192.168.0.10 IP address in the address field. Log in to the AP using the
default user name and password:
Default IP: 192.168.0.10
Username: admin
Password: admin
Once logged in, use Quick Setup and follow the online help to configure
the access point as desired.
5
Hardware Operation
LED Indicators
The LED indicators are located on the bottom portion of the enclosure,
near the cable gland.
PWR:
If the green Power LED is On, the XAP-1440
is powered. If the Power LED is Off, the XAP-1440 is
not receiving power. The Power LED blinks when
the XAP-1440 is booting.
WLAN:
If the blue LED is On, the wireless radio is
active and wireless access is enabled. Off indicates the wireless radio is not
active and wireless access is disabled.
PoE Injector:
If the Green ON LED is illuminated, power is connected to the
injector. If the ON LED is not lit, the injector is not receiving power.
Reset Button:
The Reset button is located inside the cable
gland opening of the XAP-1440 and is used to restore factory
default settings. To Restore Default Settings, with the
XAP-1440 powered on, press and hold the Reset button for
approximately 10 seconds, then release.
c
CAUTION:
Holding the Reset button for more than a few seconds
will restore the AP to factory default and remove any
custom configuration.
