Fold
Fold
Fold
Next, connect an Ethernet cable from your Router or Switch to the
Data
IN
port on the PoE Injector. Finally, connect the AC cord to the included
PoE Injector, then to the AC outlet.
n
Note:
Category-6 shielded twisted pair is recommended for best
results and stable data transmission at the highest data rates.
However, CAT5/CAT5e/CAT6 UTP cable can also be used.
PoE Injector Setup
X
Data In:
Connect an Ethernet cable from your router or switch to the
Data In
port of the included PoE Injector.
X
Data & PWR Out:
Connect an Ethernet cable from the
Data & PWR Out
port of the included PoE Injector to the PoE Port of the XAP-1410.
X
AC Power:
Connect the included AC Cord to the Power Input of the
Included Injector first and then to the AC outlet.
Power
Source
From your
Router or Switch
Luxul AP
DATA IN
DATA &
PWR OUT
POE
Injector
PoE injector
3
Preparing for Access
IP Addressing
If the XAP-1410 is connected to a network with a 192.168.0.X address
scheme, and your computer shares a similar address on the same network,
you can skip to the next step,
Access and Setup
.
n
Note:
If another device on your network shares the 192.168.0.10
address, you’ll need to temporarily reassign or remove that
device while you configure the XAP-1410.
If your network uses an address scheme other than 192.168.0.X, you’ll need
to set a temporary static IP address on the computer you’re using for config-
uration. To do so, set the IP address of your computer to an address in the
192.168.0.X range, then set the Gateway/Router address to 192.168.0.10 (the
default IP address of the XAP-1410).
Once you’re finished configuring the AP, you can return your computer’s IP
configuration to normal, typically “Obtain Automatically/DHCP.”
n
Note:
Visit
http://luxul.com/ip-addressing
to learn more about
changing your computer’s IP address and getting connected.
4
Access and Setup
Getting Connected
X
Connecting Via an Ethernet Device:
Use Ethernet cable to connect
your computer to the PoE switch or PoE injector to which the XAP-1410 is
connected. Ethernet is the preferred method of connection.
X
Connecting Via a Wireless Device:
Connect your client device to the
XAP-1410 default wireless network named
Luxul_XAP1410
or
Luxul_
XAP1410_5G
. The wireless network will run in Open Security mode, so no
passphrase is required until Wireless Security is configured.
Logging In
To access the AP’s web configuration, open your web browser and enter the
AP’s default 192.168.0.10 IP address in the address field. Log in to the AP using
the default user name and password:
Default IP: 192.168.0.10
Username: admin
Password: admin
n
Note:
If another device on your network shares the 192.168.0.10 address,
you’ll need to temporarily reassign or remove that device while
you configure the XAP-1410.
n
Note:
The XAP-1410 is not a router and will need to be connected to a
network with a router in order to deliver Internet access.
5
Hardware Operation
LED Indicators
Enclosure:
If the green Power LED is on, the XAP-1410 is powered and working.
If the Power LED is OFF, the AP is not receiving power or the LED has been
turned off in the AP’s web interface. If the green Power LED is blinking, the
XAP-1410 is booting. The two blue LEDs indicate indicate each of the 2.4GHz
and 5GHz networks are configured and broadcasting.
XAP-1410 LED’s
PoE Injector:
If the PWR LED is On, Power is Connected to the injector. If
the PWR LED is Off, the injector is not receiving power.
Reset Button
The Reset button is located underneath the mount and
marked RESET. It may be used to reboot the AP or to restore
factory default settings.
Reboot the AP:
With the XAP-1410 powered on, simply
press and release the Reset button.
Restore Factory Defaults:
With the XAP-1410 powered on,
press and hold the Reset button for 10 seconds, then release
the button and the XAP-1410 will restore factory defaults and reboot.
c
CAUTION:
Holding the Reset button for more than a few seconds
will restore the AP to factory default and remove any
custom configuration.
