LUX 301 321, Оригинальное руководство пользователя

Страница: 10 / 20

10
Setting the cutting angle
The unit allows you to set a cutting angle of up to 45°.
– Turn the locking screw (2) in the [ ] direction to
undo.
– Swing the foot plate (5) into the required angle.
– Turn the locking screw (2) in the
[ ] direction to
secure.
Setting the pendulum stroke
– Set the pendulum stroke with the switch (3):
– Switch setting [0] = Hard material
– Switch setting [1–3] = Soft material
Setting the parallel stopper
►
P. 5, item 6
– Fit the parallel stopper (16) into the holder on the
unit as shown.
– Set the parallel stopper to the required dimen-
sions and secure with the locking screw (11).
Blower
– Switch (10) in front position = Blower off (opera-
tion with dust extraction)
– Switch (10) in rear position = Blower on (opera-
tion without dust extraction)
Sawing
– Place the material to be cut on an even, suitable
surface and secure to prevent it slipping.
– Mark the cutting line or set the parallel stopper.
– Hold the device firmly with one hand and place
the front edge of the foot plate on the work
piece.
– Turn on the device.
– Press the device firmly up against the work piece
and saw slowly along the cutting line (never pull
the saw backwards!) .
Tips for sawing
– When sawing, the foot plate must rest safety and
fully on the work piece.
– When making cut-outs (e.g. cutting out parts of
kitchen worktops) first drill a hole with a suitable
diameter in the work piece and start the saw in
this hole.
– When sawing metal, apply coolant or lubrication
to the cutting line.
– When sawing small or thin work pieces always
use a stable surface or a work bench.
– Curves, circles or similar shapes must be made
at a low speed.
Things to note when sawing plastic
– When sawing plastic, if possible, use a new
blade.
– When sawing, ensure speedy operation. If you
saw too slowly, the plastic will heat up, become
soft and adhere to the teeth of the blade. The cut
will be untidy and you will need to clean the
blade.
Things to note when sawing metal
– When sawing metal, use a special blade.
– Saw with a low but even speed.
– When cutting profiles, start cutting at the thin
side.
– When cutting U-shaped profiles, start cutting at
the closed side.
Cleaning
Cleaning overview
Regularly and according to the operating condi-
tions
Troubleshooting
What to do when something doesn’t work…
In many cases, small defects can lead to a malfunc-
tion. You will usually be able to deal with these your-
self. Please refer to the table below before contact-
ing your local dealer. This may save you a lot of effort
and quite often money.
Note: A higher pendulum stroke setting
increases the cutting speed, but may lead
to rougher cut edges.
WARNING! Risk of kickback! Always
guide the saw, never the work piece!
Always hold the device tightly with both
hands.
Never pull the saw backwards!
Never tilt the blade!
DANGER! Risk of injury! Never hold the
work piece that you are working with in your
hand, on your lap, or against other body
parts.
Always clamp the work piece firmly in
place.
Do not process work pieces that are too
small to be clamped.
NOTICE! Risk of damage to the unit!
Only use saw blades that are appropriate
for the material you are processing.
Always operate the saw with gentle force.
DANGER! Risk of injury! Pull out the
power plug before conducting any mainte-
nance work on the device.
What? How?
Clean the ventilation slots
of the motor to remove
dust. Use a vacuum, cleaning
brush or paint brush.
Clean the device. Wipe the unit with a damp
cloth.
DANGER! Risk of injury! Unprofessional
repairs may mean that your unit will no
longer operate safely. This endangers you
and your environment.
GB
Stichsaege_381124_398094_301321.book Seite 10 Mittwoch, 16. September 2015 2:19 14