041588
Rev. A
11/2018
PowPak | Installation
Control Module with DALI
Test
Link
Cal.
+
For each system, ensure that you have:
One PowPak Control Module
At least one Wireless Transmitter
At least one DALI LED Driver or Fluorescent Ballast
Required Components
Radio Powr Savr Occupancy/Vacancy Sensor
(10 maximum)
Radio Powr Savr Daylight Sensor
(1 maximum)
Pico Remote Control
(10 maximum)
8 mA / 64 mA (based on model) guaranteed for the control lines.
May be pre-installed in light fixture.
Raise
Toggle
Lower
Top LED
Consult third-party DALI fixtures installation guide for fixture-specific wiring. This device can
be installed on a fixture / troffer, junction box, or marshalling box using the conduit nut or with
mounting screws. The device must NOT be mounted inside a fixture / troffer or other metallic
enclosure. Improper installation can result in degraded wireless communication, intermittent or
sustained communication failures, and will not be covered under warranty. For mounting and
wiring best practices see Lutron Application Note #620 (P/N 048620).
+
Occupancy Sensors
Daylight Sensor
Wireless Controls
Occupied:
All lights 100%.
Unoccupied:
All lights off.
Test
Link
Cal.
All lights dim in response to daylight.
On
All lights 100%
Favorite
All lights 50%
Off
All lights off
Default Functionality
2
A
Install the 1/2 in NPT to 20 mm conduit adapter (provided) onto the
PowPak Control Module.
B
The PowPak Control Module can be installed on a fixture / troffer,
junction box, or marshalling box using the conduit nut (provided) or
with mounting screws (not provided). Please consult local and national
electric codes for proper installation.
C
Once installed, energize the PowPak Control Module.
D
Use the
Toggle
“
u
” ,
Raise
“
▲
” and
Lower
“
Δ
” buttons to verify
control wiring.
English
All Wireless Transmitters must be installed within 9 m
of the PowPak Control Module with DALI.
DALI Control:
18 V
-
Guaranteed Supply Current:
•
8 mA on 4-driver controller (RMKS-DAL4-SZ)
•
64 mA on 32-driver controller (RMKS-DAL32-SZ)
Maximum Supply Current:
250 mA
220 – 240 V
~
50 / 60 Hz 50 mA
RMKS-DAL4-SZ
RMKS-DAL32-SZ
A
Connect mains wiring (hot, neutral) to each fixture.
B
Connect DALI control to each fixture.
1
DA+
DA–
NEU
HOT
DALI
MAINS
To additional DALI fixtures
Neutral
Line/Hot
DA+
DA-
+
–
WARNING! Shock Hazard.
May result in serious injury or death. Turn off power at circuit
breaker before installing the unit.
Sample LED
driver shown
Important Notes:
Please read before installing.
For installation by a qualified electrician in accordance with all local and
national electrical codes.
•
Use copper conductors only.
•
Check to see that the device type and rating is suitable for the application.
•
DO NOT
install if product has any visible damage.
•
If moisture or condensation is evident, allow the product to dry completely
before installation.
•
Operate between 0 °C and 40 °C ambient.
•
0% to 90% humidity, non-condensing.
•
For indoor use only.
Start Here
X
Vive
Programming with a Vive Hub
3
Mount, Wire, and Install DALI Devices and
Lighting Fixtures
Consult third-party device installation guide
Install PowPak Control Module
with DALI
Suggested Installation Location: Center of room to
ensure proper RF coverage of area.
A
Use an iOS or Android compatible device.
B
Download the Lutron Vive app.
C
Open the app and follow the instructions.
Note:
For further information on set up, programming, and troubleshooting with a Vive
system, please refer to the installation instructions included with the Vive hub or visit
www.lutron.com/vive-europe
Note:
For programming the PowPak Control Module with DALI without a Vive hub see
reverse side
.
Customer Assistance www.lutron.com/support
Troubleshooting
www.lutron.com / vive
Ballasts cannot be controlled locally from PowPak Control Module
with DALI.
• Ensure that the breaker(s) to the PowPak Control Module are energized.
• Ensure that the DALI control lines are wired to the lighting fixture(s).
Reset to factory defaults.
Lights do not dim as expected.
• Ensure that DALI control lines are wired properly.
Lights do not respond to Wireless Transmitter(s).
• Ensure that the breaker(s) to the PowPak Control Module and drivers/ballasts are energized.
• Ensure that Wireless Transmitters are associated to the PowPak Control Module.
• Ensure that Wireless Transmitter(s) are within 9 m of the PowPak Control Module.
Reset to factory defaults.
Lights are unstable at low-end or flash/flicker at turn-on or turn-off. • Adjust the low-end trim.
Wireless Transmitter(s) cannot be associated to PowPak Control
Module with DALI.
• Ensure that Wireless Transmitter(s) are within 9 m of the PowPak Control Module.
• The maximum number of Wireless Transmitters have been associated to the PowPak Control Module. To remove a previously set up Wireless Transmitter, tap a
Wireless Transmitter button three times; on the third tap hold for three seconds and then tap three more times.
Part of the Vive Family
vive.lutron.com
X
DALI to Fixtures
DA+ (Violet)
DA- (Violet/White)
Neutral (Blue)
Line / Hot (Brown)
Conduit Nut
1/2 in NPT to
20 mm Conduit
Adapter
Wiring a Lever
Operated Connector
When wiring lever-
operated connectors
(4 supplied) use
appropriate gauge solid or
stranded copper wire.
1
2
3
10 mm
Lutron EA Ltd | 125 Finsbury Pavement, 4th floor
London EC2A 1NQ, UK
041671
Rev. A
11/2018
Bottom
LED
9 m
maximum
Radio Powr
Savr Occupancy
Sensor
Pico
Remote
Control
PowPak
Control Module
Install in center of room
to maximize RF coverage.
PowPak
Control
Module
Wire Gauge
Total DALI-compliant
Bus Wire Length
1.5 mm
2
(14 AWG)
300 m
0.75 mm
2
(18 AWG)
150 m
0.50 mm
2
(20 AWG)
100 m
