Need Help? www.lutron.com/hilume1led or call the Lutron
®
LED Center of Excellence at 1.877.346.5338
LTE 2-Wire Forward-Phase
UL
R
Listed Driver | Installation
Important Notes:
Please read before installing.
•
For installation by a qualified electrician in accordance
with all local and national electrical codes.
•
Use copper conductors only.
•
For indoor use only.
•
Check to see that the driver type and rating are suitable
for the application.
• DO NOT
install if product has any visible damage.
•
If moisture or condensation is evident, allow the product
to dry completely before installation.
•
Operate between 32 °F (0 °C) and 104 °F (40 °C) ambient.
•
0% to 90% humidity, non-condensing.
For each system ensure you have:
English
One Compatible Lutron
R
Control
1, 2
Required Components
Install the UL
R
Listed Driver
When installing the UL
R
Listed Driver,
wire as shown.
1. Remove driver and mounting plate from the rest of the junction box.
Do not remove driver from mounting plate.
2. Using leads and ground (bundled in junction box) make power,
load, and ground connection with provided wire nuts (see wiring
diagrams).
3. Re-install LED driver and mounting plate to the junction box.
4. Ensure compatible dimmer and load are installed and restore
power to circuit. See reverse side for
Compatible Controls
.
WARNING
Shock Hazard. May result in serious
injury or death.
Turn off power at circuit
breaker before installing the unit.
Controls Requiring a Neutral Wire
Controls Not Requiring a Neutral Wire
+
041549
Rev. A
04/2016
6
Driver and junction box must be grounded in accordance with
local and national electrical codes. Ground provided by grounding
of junction box and by using the green ground wire connection.
1
See list of compatible controls on
reverse side.
2
Please refer to Installation Sheet with
your control for wiring instructions.
Lutron Electronics Co., Inc. | 7200 Suter Road
Coopersburg PA, 18036-1299
+
LTEA4U1UKL-AV120 (12 V)
LTEA4U1UKL-CV240 (24 V)
LTEA4U1UKL-XXXXX
120 V
~
50 / 60 Hz UL
R
Listed Driver
120 V
~
50/60 Hz
+ V
(Red)
From
Line / Control
To LED
Load
- V
(Black with
white stripe)
Ground
(Green)
Neutral
(White)
Dimmed Hot
(Black)
Ground / Bare
+ LED
- LED
Dimmed Hot
Neutral
4
Maximum and minimum loads are dependent on driver
output ratings. For voltage drivers, 5 W is the minimum
load requirement and 40 W is the maximum load
requirement.
5
Load ratings must match driver output ratings.
3
Driver output range is factory-set.
Different output ratings are available for different loads.
At least one UL
R
Listed Hi-lume
R
1% 2-Wire LED Driver
3
At least one compatible LED Load (light engine)
4, 5
Lutron
R
Neutral
Wire
Control
UL
R
Listed
Hi-lume
R
1% 2-Wire
LED Driver
Dimmed Hot (Black)
Hot
Neutral (White)
Neutral
Neutral
Ground
6
Ground
Ground (Green)
6
LED Light
Engine
+ V (Red)
+ LED
- V
(Black with White Stripe)
- LED
Lutron
R
Non-
Neutral
Wire
Control
UL
R
Listed
Hi-lume
R
1% 2-Wire
LED Driver
Dimmed Hot (Black)
Hot
Neutral (White)
Neutral
Ground
6
Ground
Ground (Green)
6
LED Light
Engine
+ V (Red)
+ LED
- V
(Black with White Stripe)
- LED
OR
