How-to videos
www.casetawireless.com/3way
Claro Smart Accessory Switch
Quick Install Guide
24/7 Support: 1.844.LUTRON1 (USA / Canada) +1.888.235.2910 (Mexico)
www.casetawireless.com/support
English
1. Install in accordance with all national and local electrical codes.
2. When no “grounding means” exists in wallbox, the National Electrical Code (NEC
®
) allows
a control to be installed as a replacement when a plastic faceplate with plastic fasteners is
used, or the circuit is protected by a ground fault circuit interrupter (GFCI). Lutron wallplates
meet this requirement. Cap or remove green wire before screwing control into wallbox.
3. Protect the control from dust and dirt when painting or spackling the wall.
4. Clean the accessory switch with a soft damp cloth only. Do not use any chemical cleaners.
For more information, please see www.lutron.com/cleaning
5. For indoor use only.
6. For 3-way or multi-location wiring, use only one Diva smart dimmer (DVRF-6L) or Claro smart
switch (DVRF-5NS) with up to 10 accessory switches.
7. Maximum wire length between the main control and the farthest accessory switch is 150 ft
(45 m).
Important Notes
Limited Warranty:
www.lutron.com/TechnicalDocumentLibrary/369-119_Wallbox_Warranty.pdf ©2022 Lutron Electronics Co., Inc.
Lutron, Diva, Caséta, Claro, and LED+ are trademarks or registered trademarks of Lutron Electronics Co., Inc., in the U.S. and other countries.
3-Way Wiring with a Dimmer
4-Way Wiring with a Dimmer
Ground wire
(bare or green)
Disconnect Power
WARNING: SHOCK HAZARD.
May result in Serious Injury or Death. Turn off power at circuit breaker or fuse before installing.
ON
OFF
Please read before installing
DVRF-AS
120 V
~
50 / 60 Hz 6 A
Common
(tagged)
Common
(tagged)
Blue
Red
Black
Ground wire
(bare or green)
Ground wire
(bare or green)
Line
Blue
Black
Black
Blue
Blue
Neutral
120 V
~
50 / 60 Hz
Light
Red
Line
Blue
Red
Blue
Neutral
120 V
~
50 / 60 Hz
Light
Red
Black
NOTE:
Ensure that the same wire connects to the blue wire at all locations.
NOTE:
Main switch can be placed in any location.
NOTE:
The black wire of the main switch must always connect or point towards line.
See www.casetawireless.com/3way for more details.
NOTE:
Ensure that the same wire connects to the blue wire at all locations.
NOTE:
Main dimmer can be placed in any location.
NOTE:
When using an accessory switch with a dimmer the black and red wires are reversible.
ONLY for use with:
Diva smart dimmer model number: DVRF-6L
Claro smart switch model number: DVRF-5NS
Black
Red
Red
Black
IMPORTANT:
Before disconnecting the existing devices, tag the wire connected to the different colored screw (typically black, but wire colors vary, and labeled COM). This is the Common wire.
QUESTIONS?
See www.casetawireless.com/support
IMPORTANT:
Before disconnecting the existing devices, tag the wire connected to the different colored screw (typically black, but wire colors vary, and labeled COM). This is the Common wire.
QUESTIONS?
See www.casetawireless.com/support
One to breaker and one
to light(s). For illustration
purposes only.
Do not disconnect.
Blue
Red
Black
Location 1
Location 2 (middle)
Location 3
Ground wire
(bare or green)
Common
(tagged)
Troubleshooting
Operation
Single tap the
ON
button for On (to the preset level).
Double tap the
ON
button for full brightness.
Single tap the
OFF
button for Off.
Press and hold the
OFF
button (1 second) for 30 second delayed fade-to-off.
Ground wire
(bare or green)
Common
(tagged)
Symptom
Possible Cause
The load does not turn ON or no LEDs on the
dimmer or switch turn ON.
• Front Accessible Service Switch (FASS) on the main
dimmer or switch is pulled out to the OFF position.
• Light bulb(s) burned out.
• Breaker is OFF or tripped.
• Wiring error. Refer to the wiring diagrams above or go to
www.lutron.com/wiringwizard
The load turns ON and the main dimmer or
switch works, but accessory switch does not
work.
• Wire connected to the blue wire on the main dimmer or
main switch is not the same wire connected to the blue
wire of the accessory switch.
The load does not remain ON and main
dimmer or switch LEDs glow dimly or blink.
• Blue wire is miswired to neutral wire or touching ground.
For more information, please visit www.casetawireless.com/support
Common
(tagged)
Common
(tagged)
Blue
Red
Black
Ground wire
(bare or green)
Ground wire
(bare or green)
Line /
Hot
Blue
Red
Blue
Neutral
120 V
~
50 / 60 Hz
Light
Black
Red
Black
One to breaker and one
to light(s). For illustration
purposes only.
Do not disconnect.
Blue
Black
Red
Ground wire
(bare or green)
Ground wire
(bare or green)
Line
Black
Black
Blue
Blue
Blue
Neutral
120 V
~
50 / 60 Hz
Light
Red
NOTE:
Ensure that the same wire connects to the blue wire at all locations.
NOTE:
Main switch can be placed in any location.
NOTE:
The black wire of the main switch must always connect or point towards line.
See www.casetawireless.com/3way for more details.
Black
Red
Red
Location 1
Location 2 (middle)
Location 3
Ground wire
(bare or green)
Common
(tagged)
Common
(tagged)
Single tap the
ON
button for On.
Single tap the
OFF
button for Off.
Press and hold the
OFF
button (1 second) for 30 second delayed off.
Accessory Switch with a
Dimmer
Accessory Switch with a
Switch
White
Switch
Accessory
Switch
Switch
Accessory
Switch
NOTE:
Ensure that the same wire connects to the blue wire at all locations.
NOTE:
Main dimmer can be placed in any location.
NOTE:
When using an accessory switch with a dimmer the black and red wires are reversible.
Dimmer
Accessory
Switch
Dimmer
Accessory
Switch
Dimmer
Accessory
Switch
Accessory
Switch
Dimmer
Accessory
Switch
Accessory
Switch
Switch
Accessory
Switch
Accessory
Switch
Switch
Accessory
Switch
Accessory
Switch
ON
OFF
3-Way Wiring with a Switch
4-Way Wiring with a Switch
Blue
Red
Black
Blue
Black
Red
Blue
Red
Black
Blue
Red
Black
White
Blue
Black
Red
Blue
Black
Red
P/N 0302061 REV A
