background image

 

 

NOTE

: If the battery does not fit properly, disconnect it and confirm that the battery pack is the correct 

model for this charger as shown on the specification chart. Do not charge any other battery pack or any 
battery pack that does not securely fit the charger. 

 

Frequently monitor the charger and battery pack while connected. 

 

Unplug the charger and disconnect it from the battery pack when finished. 

 

Store the charger and battery pack indoors, out of reach of children. 

NOTE

: If the battery is hot after continuous use, allow it to cool down to room temperature before 

charging. This will extend the life of your battery.  

 

9   OPERATION INFORMATION SPECIFIC FOR  

THE OSCILLATING TOOL 

9.1

 

To install or remove the battery pack.(Fig. 2)  

 

Fig. 2  

1.

 

Turn the ON/OFF switch button of this tool to its “

OFF

” position. 

2.

 

To install, slide the battery pack into the battery port. Make sure the latches on each side of the 
battery pack snap into place and battery pack is secured in the tool before beginning operation. 

3.

 

To remove, locate latches on both sides of battery pack and depress both sides to slide out battery 
pack from the cordless Multi Function Tool body. 

9.2

 

LED battery indicators (Fig. 3)  

The machine has 3 LED battery indicators located on 
the top of the tool. 
L1:Green  /  L2:yellow  /  L3:red 
The battery capacity status can be checked by 
switching the tool on and pressing the ON/OFF switch 
button. 
The LED lights give you an idea of the capacity level of 
the battery: 
If all 3 LEDs are lit: The battery is fully charged. 
If L1 & L2 are lit: the battery has about 60% of its 
capacity left. 
If only L3 is lit : the battery is almost discharged and 
should be recharged. 

 

Fig. 3  

To ensure proper performance, always check if the battery is full enough for prior to operation. 

NOTE

: The LED battery indicators always light during operation. 

NOTE

: Please charge the battery after each use.  If the tool is not used frequently, it is recomended to 

charge the battery on a monthly basis. 

9

Содержание LT62068




















Отзывы: