LumaSense LumaSMART Скачать руководство пользователя страница 47

Страница: 47 / 148

LumaSMART

User Manual

Installation of the LumaSMART® Controller

•

Using the red Viton

caps supplied with the cable, cover the connector ends during fiber optic cable

installation.

Tape the pull wire to at least 152.5 mm (6 in) of the outside fiber optic cable and then pull the fiber optic

cable through the conduit. (Add conduit diameter).

Label and connect all cables through the bottom of the LumaSMART controller. Fiber Optic probe

channels start from back to front (Channel 1 through Channel 4).

LumaSMART Controller FOT Connections (Front Facing Upward)

Store the excess fiber optic cable in 152.5 mm (6 in) diameter loops.

4.3

Installing the Electrical Wiring

The following are directions to electrically wire the LumaSMART power, outputs and infrastructure

communication. The table below outlines the standard configuration, as well as the optional infrastructure

communication.

Table 5: LumaSMART Standard Configuration

Characteristic

Specification

Analog Output

4 to 20 mA or 0 to 1 mA

Programmable Relays

0, 8 or 16 Form-C

System Status Relay

1 Form-C

Optional (Infrastructure) Communication

RS485, RS232, Ethernet

Protocols

IEC 61850, Modbus, DNP3 or ASCII

Содержание LumaSMART





















































































































































Результаты поиска

Содержание LumaSMART

Отзывы:

Бренды по названию

Популярные бренды

LumaSense LumaSMART, Руководство пользователя

Результаты поиска

Содержание LumaSMART

Отзывы:

Бренды по названию

Популярные бренды