manualshive.com logo in svg

Lumag Rambo HC15, Руководство оператора

Поделиться
Скачать
Lumag Rambo HC15 Скачать руководство пользователя страница 20

Part VI: Troubleshooting and Parts List 

 

12 

 

PART V: Troubleshooting and Parts List 

Most  problems  are  easy  to  fix.  Consult  the  Troubleshooting  Table  below  for  common 

problems and their solutions. If you continue to experience problems, contact the dealers in 

your area. 

 

 

 

 

WARNING 

Before  performing  any  maintenance  procedure  or  inspection,  stop  the  engine,  wait  five 

minutes to allow all parts to cool. Disconnect the spark plug wire, keeping it away from the 

spark plug. 

 

Troubleshooting Table 

SYMPTOM 

POSSIBLE CAUSE 

The engine won’t start. 

 

(Please refer to the 

engine user manual 

for engine-specific 

procedures.) 

 

Is the ignition switch in the “ON” position? 

 

Is the fuel shut-off valve on? 

 

Are you using fresh, clean gas? If the gas is old, change it. Use         
a fuel stabilizer if you keep gas longer than 30 days. 

 

Is the spark plug clean? If the spark plug is dirty or cracked,     
change it. If it’s oily, leave it out, hold a rag over the plug hole and 
pull the recoil cord several times to blow out any oil in the 
cylinder, then wipe off the plug and reinsert it. 

The engine lacks power 

or is not running 

smoothly. 

 

 

(Please refer to the 

engine user manual 

for engine-specific 

procedures.) 

 

Check that the Throttle Lever is in the “Run” position. 

 

Is  the  air  filter  clean?  If  it’s  dirty,  change  it  following  the 

procedure in the engine manufacturer’s owner’s manual. 

 

Is the spark plug clean? If it’s fouled or cracked, change it. If it’s 

oily,  leave  it  out,  hold  a  rag  over  the  plug  hole  and  pull  your 

recoil cord several times to blow out any oil in the cylinder,    then 

wipe off the plug and reinsert it. 

 

Are you using fresh, clean unleaded gas? If it’s old, change it. Use 

a fuel stabilizer if you keep gas longer than 30 days. 

 

Does your engine have the right amount of clean oil? If it’s dirty, 

change  it  following  the  procedure  in  the  engine  manufacturer’s 

owner’s manual. 

 

Check the oil level and adjust as needed. 

Engine smokes. 

 

(Please refer to the 

engine user manual 

for engine-specific 

procedures.) 

 

Check the oil level and adjust as needed. 

 

Check the air filter and clean or replace if needed. 

 

You  may  be  using  the  wrong  oil—too  light  for  the  temperature. 

Refer to your Engine Owner’s Manual for detailed information. 

 

Clean the cooling fins if they’re dirty. 

Содержание Rambo HC15

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды