Lumag HGS50058, Руководство оператора

Страница: 15 / 28

In the case of emergency release both
levers on the handlebar immediately.
The levers will return to the zero position, the
machine will stop and the safety brake will stop
the mowing rotor in a very short time.
3. Operating lawn mowers 5316SBE, 5316SPE
Move the accelerator control lever on the right
handlebar to MAX position. Start the engine. Follow
the instructions in the engine instruction manual.
When starting the engine, both clutch levers (1) and
(3) fig. 5 on the handlebars shall be released. Set
max. revolutions of the engine by the accelerator
lever. Hold the handlebar grips. Press the lever with
the safety catch (3) fig. 5 on the right handlebar.
Press the lever very slowly by two thirds so that the
mowing rotor can start turning and the engine does
not stop. The starting of the mowing rotor is accom-
panied by partial slipping of the V-belt and relating
phenomena (rattling, screeching). Upon complete
start-up of the rotor, press the lever fully towards the
grip. The propelling mechanism is actuated by
means of the lever (1) fig. 5 on the left handlebar.
Press the lever towards the grip, and the machine
will start moving.
6. Stopping lawn mower 5316SLE
If you operate the machine with the horizontal bar
tilted down (4) fig. 13, hold the lever (3) fig. 13 by
your right hand and release the grab handle, or re-
lease the lever (1) fig. 13 by your left hand, and the
machine will stop moving. Release the right lever (3)
fig. 13 slowly to switch off the mowing rotor drive.
When turning or backing with the machine, the mo-
wing rotor need not be stopped so as not to waste
the energy of the turning rotor. Switch the engine off
by moving the accelerator lever (2) fig. 13 to MIN or
STOP position.
The procedure of adjusting the position of handlebars
1 .Loosen the lever of a clamp joint no. 1 by one revolution
2. Loosen the lever of position no. 2 arrest by 3
revolutions
3. Adjust the handlebars to required position
yellow arrows
on the tube of the upper part point at the yellow division
of individual positions on the lower part.
4. Tighten the lever of position no. 2 arrest.
5. Tighten the lever of clamp joint no. 1.
HANDLEBAR POSITION SIDE ADJUSTMENT RIGHT
HANDLEBAR POSITION HEIGHT ADJUSTMENT I
- 2 2 -
4. Stopping lawn mowers 5316SE, 5316SPE
Release the left lever (1) fig. 5, and the machine
will stop moving. Release the right lever (3) fig. 5
slowly to switch off the mowing rotor drive. When
turning or backing with the machine, the mowing
rotor need not be stopped so as not to waste the
energy of the turning rotor. Switch the engine off by
moving the accelerator lever to MIN or STOP position.
5. Operating lawn mower 5316SLE
Move the accelerator control lever (2) fig. 13 on the
right handlebar to MAX position. Start the engine.
Follow the instructions in the engine instruction ma-
nual. When starting the engine, both clutch levers
(1) and (3) fig. 13 on the handlebars shall be re-
leased. Set max. revolutions of the engine by the
accelerator lever. Hold the handlebar grips. Press
the lever with the safety catch (3) fig. 13 on the right
handlebar. Press the lever very slowly by two thirds
so that the mowing rotor can start turning and the
engine does not stop. The starting of the mowing
rotor is accompanied by partial slipping of the V-belt
and relating phenomena (rattling, screeching). Upon
complete start-up of the rotor, press the lever fully
towards the grip. The propelling mechanism is
actuated by means of the lever (1) fig. 13 on the left
handlebar. Press the lever towards the grip, and the
machine will start moving. When mowing, you can
make use of a tilting horizontal bar (4) fig. 13, and
operate the machine by one hand.
HANDLEBAR POSITION TRANSPORT