manualshive.com logo in svg

Lull 944E-42, Руководство по обслуживанию

Сервисное руководство Lull 944E-42 доступно для бесплатной загрузки на manualshive.com. Этот мануал предоставляет подробные инструкции по обслуживанию и ремонту продукта. Скачайте его сейчас, чтобы получить всю необходимую информацию для правильного ухода за вашим устройством.

Поделиться
Скачать
background image

8.179

Model 644E-42/944E-42

Rev. 6/04

Hydraulic System

b. Main Control Valve Disassembly

1. To disassemble the main control valve (1), remove 

the four hex socket head capscrews (2) which hold 
the inlet section (3), transfer carriage section (4), 
auxiliary hydraulic section (5) to the mono block 
section (6).

IMPORTANT:  Refer to Section 8.7, “Hydraulic System 
Testing,” to properly test and reset any relief valve 
pressure settings if necessary.

2. The four socket head capscrews (2) are threaded 

into the mono block section (6). Pull the four 
capscrews all the way out of the sections.

Inlet Section Disassembly

1. Remove the inlet section (3) from the transfer 

carriage section (4). Remove the three small o-rings 
(7) and the large o-ring (8) from between the 
sections. Discard the o-rings.

2. Remove the main relief valve (9) from the inlet 

section (3). Remove and discard all seals.

Note:  The internal parts of the relief valves are not 
serviceable. Replace the entire relief valve if necessary.

3. Remove the unloader valve (10) from the inlet 

section (3). Remove and discard all seals.

Note:  The internal parts of the unloader valve are not 
serviceable. Replace the entire unloader valve if 
necessary.

Transfer Carriage Section Disassembly

1. Remove the transfer carriage section (4) from the 

auxiliary hydraulic section (5). Remove the three 
small o-rings (11) and the large o-ring (12) from 
between the sections. Discard the o-rings.

2. Remove the relief valves (13 & 14) from the transfer 

carriage section (4). Remove and discard all seals.

Note:  The internal parts of the relief valves are not 
serviceable. Replace the entire relief valve if necessary.

3. Remove the hex socket head capscrews (15) holding 

the spool end housings (16) to the section. Remove 
the housings, o-rings (17), springs (18) and pistons 
(19). Discard the o-rings.

Note:  The spool in the section is not serviceable 
separately. If the spool is scratched or nicked the entire 
section must be replaced.

4. Remove the hex plug (20) and o-ring (21) from the 

top of the section. Discard the o-ring. The two 
plungers (22) of the compensator are not serviced 
separately. If these parts require replacement the 
entire section has to be replaced.

5. Remove the spring (23) from between the plungers.

Auxiliary Hydraulic Section Disassembly

1. Remove the auxiliary hydraulic section (5) from the 

mono block section (6). Remove the three small o-
rings (24) and the large o-ring (25) from between the 
sections. Discard the o-rings.

2. Remove the relief valves (26 & 27) from the auxiliary 

hydraulic section (5). Remove and discard all seals.

Note:  The internal parts of the relief valves are not 
serviceable. Replace the entire relief valve if necessary.

3. Remove the hex socket head capscrews (28) holding 

the spool end housings (29) to the section. Remove 
the housings, o-rings (30), springs (31) and pistons 
(32). Discard the o-rings.

Note:  The spool in the section is not serviceable 
separately. If the spool is scratched or nicked the entire 
section must be replaced.

4. Remove the hex plug (33) and o-ring (34) from the 

top of the section. Discard the o-ring. The two 
plungers (35) of the compensator are not serviced 
separately. If these parts require replacement the 
entire section has to be replaced.

5. Remove the spring (36) from between the plungers.

Содержание 944E-42













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 944E-42

Ravas 1100 Operational Manual preview
1100
Бренд: Ravas Страницы: 14
KAUP 3T456ZA Operating Manual preview
3T456ZA
Бренд: KAUP Страницы: 24
Manitou MT 733 EASY 75D ST5 S1 Basic Instruction Sheet preview
MT 733 EASY 75D ST5 S1
Бренд: Manitou Страницы: 2
Manitou MT 732 EASY 75D ST3B S1 Basic Instruction Sheet preview
MT 732 EASY 75D ST3B S1
Бренд: Manitou Страницы: 2
Manitou MT 625 H EASY 49K ST3A S1 Instructions preview
MT 625 H EASY 49K ST3A S1
Бренд: Manitou Страницы: 2
Manitou Mattoc Pro Service Manual preview
Mattoc Pro
Бренд: Manitou Страницы: 34
Manitou MT10044XT Operators & Service Manual preview
MT10044XT
Бренд: Manitou Страницы: 114
Manitou MSI 40 T S3 ST3B Operator'S Manual preview
MSI 40 T S3 ST3B
Бренд: Manitou Страницы: 114
Manitou MSI 20 D Operator'S Manual preview
MSI 20 D
Бренд: Manitou Страницы: 116
Manitou MC 40 Powershift Manual preview
MC 40 Powershift
Бренд: Manitou Страницы: 102
Manitou MT-X 625 2-E3 Series Operator'S Manual preview
MT-X 625 2-E3 Series
Бренд: Manitou Страницы: 132
Manitou MT 1058 R PRIVILEGE Manual preview
MT 1058 R PRIVILEGE
Бренд: Manitou Страницы: 139
Manitou MLT625-75 H S1-E3 Operator'S Manual preview
MLT625-75 H S1-E3
Бренд: Manitou Страницы: 160
Kelvin Mini Series Maintenance Instructions Manual preview
Mini Series
Бренд: Kelvin Страницы: 29
Baoli CPDS15 Operation & Service Manual preview
CPDS15
Бренд: Baoli Страницы: 87

Бренды по названию

Популярные бренды

Загрузить еще бренды