Lufft CHM 15k Скачать руководство пользователя страница 29

Страница: 29 / 73

Operating Manual CHM 15k

R13 / 07-2019

Communication via RS485 & Ethernet

Table 4

List of configurable parameters,

can be set in service mode,

Web

format for web interface, or only in web interface available

RS485

format for RS458, or only for RS485 available

Parameter

Short
cmd

RS485

Default
value

Description

APDBreakdown

UBR

Device-dependent (e.g. 400000 mV)

ApdTempGradient

TCO

2400

value for comparison [mV/K]

IPDhcp

IPD

IP address DHCP

LaserPower

LAP

Device-dependent (e.g. 50 mW)

LifeTime(h)

LIT

hours the laser diode is in operation

Parameters

RS485

Delivers a list of all parameters that are
available in the RS485 mode

SerLOM

LOM

TUByyxxxx Serial number of the laser optical module

(LOM)

SystemLifeTime(h)

SLT

Total number of all operating hours of the
CHM system

TBCalibration

TBC

Scaling factor compared to reference

VersionFirmware

VFI

Firmware version
(data processing and handling)

VersionFPGA

VFP

Firmware FPGA

VersionLinux

VLI

Operating system version

Table 5

List of read-only parameters, accessible via the RS485 interface.

RS485

only for RS485 available

Explanatory notes to Table 4

AFDMode:

Switch on / off the automatic file distribution system via LAN / WAN / DSL, see

http://www.dwd.de/AFD/ for more information or section

8.8

Altitude(m):

Specification of the height of the location above sea level in meters. In NetCDF files, the

parameter CHO (Cloud Base Offset) is used instead. Both are logically combining the variables Altitude
and UseAltitude.

Azimuth:

Specification of the horizontal angle in degrees.

Baud:

Change baud rate (see 8.2.3 Changing the baud rate).

BaudAfterError:

Default baud rate after communication error (see 8.2.3 Changing the baud rate).

BlowerMode:

Used to test the window fans and switch to different operating modes.

Mode 2 “rest at night”

works only correctly if the parameter TimeZoneOffsetHours is set correctly, too.
0 = hourly check and weather-dependent, 1 = no hourly check from 22:00 to 06:00, 2 = off from 22:00 to
06:00, 3 = always on, 4 = always off.

DataTime:

Sets the date and time (see 8.2.5)

Содержание CHM 15k










































































Результаты поиска

Содержание CHM 15k

Отзывы:

Похожие инструкции для CHM 15k

Бренды по названию

Популярные бренды

Lufft CHM 15k, Руководство пользователя

Результаты поиска

Содержание CHM 15k

Отзывы:

Похожие инструкции для CHM 15k

Бренды по названию

Популярные бренды