Lufft ARS31-UMB Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 40

Lufft ARS31-UMB Скачать руководство пользователя страница 36

ARS31(Pro)-UMB

Operating Manual V9/03.2017

G. Lufft Mess- und Regeltechnik GmbH, Fellbach, Germany

36

11 Troubleshooting

Description

Cause / remedy

The sensor will not allow
polling requests.

-

Sensor (no dummy cover) installed

-

Check power supply voltage in the connection
(terminal) box and on the sensor

-

Check interface connection

-

False device ID



check ID

-

RS485 cable A / B reversed

-

False baud rate set (sensor, ISOCON-UMB)

-

False protocol set or used (binary, ASCII)

Freezing temperature is
not calculated.

-

Start conditions not fulfilled (road temperature above
set temperature)

-

Sensor surface dry

-

Measurement cycle not yet completed (lasts up to 20
minutes)

-

Interference during calculation of freezing temperature
due to external influences in critical phases of the
measurement cycle

-

Sensor surface heavily soiled -> clean sensor surface
with water

-

Green protective foil not removed ->

remove green

protective foil

Determined freezing
temperature is reset after
a few minutes

-

Sensor is resetting. Query channel 20001 and check
that the value is incremented. After reaching 60000
the counter starts again from “0”. If the value goes to
“0” earlier, the sensor has made a restart. Power
supply must be checked (see chapter 6.2.1.1)

-

Power supply overloaded

-

Unstable power supply

-

Related to an LCOM-UMB: Misconfiguration of LCOM,
thereby resetting the UMB-Modules every x minutes
(default is 15 Minutes)

Salt concentration channel
delivers error message

-

Start conditions not fulfilled (road temperature above
set temperature)

-

Sensor surface dry

-

Measurement cycle not yet completed (lasts up to 20
minutes)

-

Interference during calculation of freezing temperature
due to external influences in critical phases of the
measurement cycle

-

Sensor surface heavily soiled ->

clean sensor surface

with water

-

Green protective foil not removed->

remove green

protective foil

Threat of icing channel
delivers error FC:36

-

Threat of icing is disabled or not supported (ARS31-
UMB)

The description of the UMB-errorcodes

you can find in the document “UMB-Protocol” under

in

the sector Support

– Downloads – Manuals – UMB Technology.

«
...
34
35
36
37
38
...
»

Содержание ARS31-UMB









































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды