Lufft 8511.EAK Скачать руководство пользователя страница 7

Страница: 7 / 158

General

The introduction of UMB technology has enabled Lufft to offer low cost sensors for

road traffic technology. UMB sensors can be combined using ISOCON modules and

additional analog sensors can be integrated with the ANACON module.

The

LCom

- Lufft Communicator

– was developed to provide the UMB sensor data

over various communication protocols.

LCom consists of an embedded computer with Windows CE operating system, a

touchscreen display (resolution 800x480 pixels and CFL backlighting), and interfaces

for a GPRS modem, Party-Line modem and UMB network as well as an Ethernet and

USB interface. In addition, LCom has a real-time clock with battery backup.

Currently following protocols are supported:

•

TLS97

•

TLS2002

•

TLS2012

•

TLS over IP (Asfinag)

•

NTCIP (via SNMP)

•

MSSI (SOAP) (Lufft/Asfinag)

In TLS mode, LCom operates as an

“integrated control module with EAK” (Inselbus),

or as “EAK on external control module” (Lokalbus).

Additional protocols planned are:

•

DGT (Spain)

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды