manualshive.com logo in svg

Lucent Technologies PARTNER Advanced Communications System Release 1.0, Инструкция по программированию и эксплуатации

Поделиться
Скачать
Lucent Technologies PARTNER Advanced Communications System Release 1.0 Скачать руководство пользователя страница 330

PARTNER MAIL Voice Messaging System Release 3 Planning Forms
(585-322-517) provides the forms needed to plan and record how your
PARTNER MAIL system is to be programmed.

PARTNER MAIL Voice Messaging System Release 3 User’s Guide
(585-322-518) contains instructions for using the PARTNER MAIL system.

Some of these materials also are available in Spanish and French.  For more
information, or to order materials, contact the Lucent Technologies BCS
Publications Center at 1 800 457-1235 or 1 317 361-5353 or your Lucent
Technologies Representative or local Authorized Dealer.

Hardware Components

Ordering additional telephones and modules, accessories, and replacement
parts for your system is convenient.  Table B-1 shows where you can buy system
components in the continental United States.

To take full advantage of your system, the sources shown below also can
provide you with the optional equipment you might want for your system, such as
Lucent Technologies fax machines, answering machines, standard phones,
voice messaging systems, modems, paging systems, doorphones, headsets,
bells, lights, strobes, music-on-hold systems, and printers.

You can obtain most items from more than one source, either directly from
Lucent Technologies or from authorized dealers.  Sources in the U.S. are:

Lucent Technologies Catalog Sales.

  This source is Lucent

Technologies’ national phone/mail sales center in Cincinnati.  A Catalog
Associate will place your order, including Lucent Technologies installation
if you need it.  You can charge your order on a VISA, Mastercard, or
American Express card.  The Catalog Associate can also give you sales
advice and mail you the Lucent Technologies SOURCEBOOK CATALOG
of systems, telephones, and accessories.  Call 1 800 451-2100.

Lucent Technologies Sales Offices.

  Sales offices to serve the small

business customer are located throughout the country.  To contact the
office closest to you, call 1 800 247-7000.  A representative will place
your order, including Lucent Technologies installation if you need it.

Lucent Technologies Authorized Dealers.

  You can also buy most

items from one of Lucent Technologies’ authorized dealers.  Check your
local telephone directory’s yellow pages for the Lucent Technologies
Authorized Dealer nearest you.

Lucent Technologies National Parts Sales Center.

  This national sales

center, located in Denver, stocks replacement parts.  Telephone orders
can be placed by calling 1 800 222-7278.

In Canada, order these items from Lucent Technologies Canada:

Eastern Canada and Ottawa:

1 514 335-7200

Ontario: 1 

416 

756-5236

Central and Western Canada:

1 800 561-5165

Maintenance

    B-5

Содержание PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды