Lucent Technologies PARTNER Advanced Communications System Release 1.0 Скачать руководство пользователя страница 242 | Manualshive

Страница: 242 / 365

background image

Restore Programming (#125)

Description

This System Programming procedure enables you to reinstate your system and
telephone programming (except the System Day, System Date, and System
Time) to the settings saved on a PC Card at the last system backup (manual or
automatic). This procedure is useful if your system settings become corrupted, if
you make changes and decide you would rather use the former settings, or if you
replace your processor module and want to retain the system settings you had
on the previous processor module. A successful restore takes about five
seconds.

NOTE:

When a restore completes successfully, the

Restore Complete

message

displays for two seconds at idle extensions 10 and 11, and then a

System

Reset—Programming Saved (#728)

occurs,

disconnecting any calls in

progress. It is recommended that you warn users before beginning a restore, or
do the restore during nonbusiness hours.

Related Features

Backup Programming—Automatic (#123

) automatically saves your

programmed settings at regular intervals.

Backup Programming—Manual (#124)

is a manual procedure that you can

perform at any time to back up your system and telephone programming
settings.

System Reset—Programming Saved (#728)

automatically occurs following

a successful restore. The reset disconnects any calls in progress.

Considerations

If the restore is not successful, the display shows

Restore Failed

or

Restore Failed-Try Again

for two seconds. All calls that were in

progress are disconnected and all of the system and telephone
programming settings revert to the default settings.

The PC Card in the PC Card slot must be a PARTNER ACS Backup/Restore
PC Card, which can be purchased from Lucent Technologies.

PC Card Slot 2 is recommended for the Backup/Restore PC Card; however,
either slot can be used. If the system detects Backup/Restore PC Cards in
both slots when a restore begins, the first slot is used and the second is
ignored.

Valid Entries

1 = MAN.

mmddyy

✔

(where

mmddyy = the month, day, and year)

2 = AUTO.

mmddyy

Restore Programming (#125)

5-149

«
...
240
241
242
243
244
...
»

Содержание PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PARTNER Advanced Communications System Release 1.0

Бренд: zipwake Страницы: 12

Бренд: jbc Страницы: 12

Бренд: Handicare Страницы: 56

Бренд: ZETRON Страницы: 3

Бренд: Magnavox Страницы: 23

Бренд: Grundig Страницы: 16

Бренд: HEIDENHAIN Страницы: 64

duplex DC -24 II

Бренд: JETI model Страницы: 52

Auto Sentry Petro

Бренд: ICS Страницы: 42

Бренд: Powerdist Страницы: 7

Бренд: TechniSat Страницы: 24

Бренд: RCA Страницы: 2

RS2181i/RS2181iF

Бренд: RCA Страницы: 1

RS2052 - Compact Bookshelf System

Бренд: RCA Страницы: 20

Бренд: RCA Страницы: 26

Бренд: Hitachi Страницы: 14

Бренд: Hitachi Страницы: 4

Бренд: Hitachi Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды