Lucent Technologies Network Access Module Скачать руководство пользователя | Manualshive

Страница: 66 / 75

background image

INA Module Maintenance Options

C-6

INA Module Installation and Configuration Guide

Demand Tests

The INA module board incorporates three new demand tests:

•

Line loopback

•

Payload loopback

•

Bit error rate test (BERT)

Line Loopback Test

The line loopback test loops the T1 signal back towards the network without
regenerating framing and without recalculating a cyclic redundancy test (CRC)
checksum. To perform this test, you must first busy out the INA module. From your
system programming console, use the following sequence to start the line loopback test:

Menu: Maintenance

→

Slot

→

Slot#

→

Enter

→

Demand test

→

LineLpbk

After the line loopback test has been started, selecting

→

Back terminates the test.

Note – During the line loopback test, the INA module transmit clocking is derived from
the signal received by the INA module. The remote end of the T1 connection must be
set up as the clock master for the T1/PRI inrfco v(o)6.5il tilcloo

«
...
64
65
66
67
68
...
»

Содержание Network Access Module












































































Отзывы:

Нет отзывов

Похожие инструкции для Network Access Module

Бренд: D-Link Страницы: 38

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 22

Бренд: D-Link Страницы: 20

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 12

DIR-615 - Wireless N Router

Бренд: D-Link Страницы: 13

Бренд: D-Link Страницы: 124

Web Smart DES-1210-28P

Бренд: D-Link Страницы: 6

2Voice + 4SW VoIP Router DVG-1402S

Бренд: D-Link Страницы: 57

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 23

Express EtherNetwork DI-604

Бренд: D-Link Страницы: 7

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 97

SharePort DIR-825

Бренд: D-Link Страницы: 2

Amplifi DIR-645

Бренд: D-Link Страницы: 28

DHI-NVR2104-P-4KS2

Бренд: Dahua Страницы: 23

Бренд: EMCIS Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды