Lucent Technologies Galaxy Power System 4812 Скачать руководство пользователя страница 107

Страница: 107 / 132

Lucent Technologies Galaxy Power System 4812

Issue 5 June 2000

Troubleshooting Millennium Systems 13 - 9

CTRL

MAJ

Controller Fail

•BSH failure

•BSJ failure

•Option board

failure

•Display failure

•BIC failure

→

1. Strap K1, K2, K3 on

BLJ3 from “C” to “R”
prior to replacing BIC.
See Figure 8-2.

2. Replace BIC.

CTRL

MAJ

Circuit Pack Fail

See “Controller
Fail”.

See “Controller Fail”.

CTRL

MAJ

Controller Fuse

Fuse has
operated.

Replace the controller fuse
labeled F2 (intelligent
power).

CTRL

MAJ

Alarm Battery
Supply Fuse

Fuse has
operated.

Replace the controller fuse
labeled F5 (alarm battery
supply).

CTRL

MAJ

Remote Peripheral
Fuse

Fuse has
operated.

Replace the controller fuse
labeled F1 (option power).

CTRL

MAJ

Sense/Control Fuse

Fuse has
operated.

Replace the controller fuse
labeled F4 (voltage sense).

CTRL

MAJ

Bay Interface ID
Conflict

Two or more bay
interface cards
(BICs) have the
same ID number.

Following instructions
printed on the label over the
BIC, adjust the DIP
switches to change the ID
number.

CTRL

MAJ

Major
Communication
Fail Alarm

Blinking
ALM LED
on rectifiers

red LED on
BIC

Loss of
communication
with controller:

•Defective

interface from
BIC or multiple
rectifiers to
controller

•Internal failure

of controller,
BIC, or multiple
rectifiers

1. Verify that the controller

is powered and operating
correctly.

2. If there are no controller

alarms, replace the
equipment that has lost
communication.

•If the problem is not

corrected, call your local
RTAC representative.

Table 13-C: Controller Alarms

(See Figures 12-2 and 12-3)

Controller

LED

Controller

Alarm

Status

Millennium

Controller Display

Other

Indication(s)

Possible

Problem(s)

Possible Solution(s)

Содержание Galaxy Power System 4812





































































































































Результаты поиска

Содержание Galaxy Power System 4812

Отзывы:

Похожие инструкции для Galaxy Power System 4812

Бренды по названию

Популярные бренды

Lucent Technologies Galaxy Power System 4812, Руководство по эксплуатации продукта

Результаты поиска

Содержание Galaxy Power System 4812

Отзывы:

Похожие инструкции для Galaxy Power System 4812

Бренды по названию

Популярные бренды