manualshive.com logo in svg

Lucent Technologies DSP1611, Информационное руководство

Продукт "Lucent Technologies DSP1611" – это цифровой сигнальный процессор с высокой производительностью. Чтобы получить изделие "Lucent Technologies DSP1611" Information Manual, вы можете скачать руководство с сайта manualshive.com абсолютно бесплатно. В нем содержится важная информация о работе продукта.

Поделиться
Скачать
background image

DSP1611/17/18/27/28/29 DIGITAL SIGNAL PROCESSOR

Information Manual

Serial I/O

April 1998

7-12

DRAFT COPY  

Lucent Technologies Inc.

7.3 Serial I/O Pin Descriptions

The physical serial I/O port consists of 12 signals: four are used for serial input, five are used for serial output, and 
three are used in multiprocessor applications, TDM applications, or both.

Table 7-4

 lists each signal with its type 

and description.

Table 7-4. DSP1611/17/18/27/28/29 Serial I/O Pins

Symbol

Type

Name/Description

DI

I

Data Input. Serial data latched on the rising edge of ICK, either LSB or MSB first corre-
sponding to the sioc register MSB field.

 ICK

I/O

†

† 3-stated.

Input Clock. Clock for serial input data. Corresponding to the sioc register ICK field in 
active mode, ICK is an output; otherwise in passive mode, ICK is an input.

ILD

I/O

†

Input Load. Falling edge of ILD indicates the beginning of a serial input word. Correspond-
ing to the sioc register ICK field in active mode, ILD is an output; otherwise in passive mode, 
ILD is an input.

IBF

O

†

Input Buffer Full. IBF is asserted if the input buffer is filled and negated by a read of the 
buffer. IBF is also negated by asserting RSTB.

DO

O

†

Data Output. Serial data output from the output shift register (osr), either LSB or MSB first, 
corresponding to the sioc register MSB field. DO changes on the rising edges of OCK for 
the DSP1611/17/18. For the DSP1627/28/29, DO changes on the rising or falling edge of 
OCK corresponding to the DODLY bit in the sioc register. DO is 3-stated if DOEN is high.

DOEN

I/O

†

Data Output Enable (Active-Low). An input if not in the multiprocessor mode. DO and 
SADD are enabled only if DOEN is low. In the multiprocessor mode (tdms register MODE 
field set), DOEN indicates a valid time slot for a serial output and is bidirectional.

OCK

I/O

†

Output Clock. Clock for serial output data. Corresponding to the sioc register OCK field in 
active mode, OCK is an output; otherwise in passive mode, OCK is an input.

OLD

I/O

†

Output Load. Clock for loading the output shift register (osr) from the output buffer 
(sdx[out]).  A falling edge of OLD indicates the beginning of a serial output word. Corre-
sponding to the sioc register OLD field in active mode, OLD is an output; otherwise in pas-
sive, OLD is an input.

OBE

O

†

Output Buffer Empty. OBE is asserted if the output buffer is emptied (moved to the output 
shift register for transmission). It is cleared with a write to the buffer (sdx). OBE is also set 
by asserting RSTB.

SADD

I/O

†

Serial Address (Active-Low). A 16-bit serial bit stream typically used for addressing during 
multiprocessor communication between multiple DSP devices. In multiprocessor mode, 
SADD is an output if the tdms time slot dictates a serial transmission; otherwise, it is an 
input. Both the source and destination DSP are identified in the transmission. SADD is 
always an output when not in multiprocessor mode and can be used as a second 16-bit serial 
output. SADD is 3-stated if DOEN is high and must be tied high through a resistor when 
used in multiprocessor applications.

SYNC

I/O

†

Multiprocessor Synchronization. Typically used in the multiprocessor mode. A falling 
edge of SYNC indicates the first word of a TDM I/O stream and causes the synchronization 
of the active ILD and OLD generators. SYNC is an output if the tdms register SYNC field is 
set; otherwise, it is an input. SYNC must be tied low if it is not used as an output. If used as 
an output, SYNC = ILD/OLD 

÷ 

8 or 16 corresponding to the setting of the SYNCSP field of 

the tdms register. This procedure can be used to generate a slow clock for SIO operation.

Содержание DSP1611




























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSP1611

dbx 902 Manual preview
902
Бренд: dbx Страницы: 8
Dahua DHI-NVR5224-24P-4KS2 Quick Start Manual preview
DHI-NVR5224-24P-4KS2
Бренд: Dahua Страницы: 24
National Instruments NI 9213 Getting Started preview
NI 9213
Бренд: National Instruments Страницы: 11
Teagle Tomahawk 7100 Operator'S Manual preview
Tomahawk 7100
Бренд: Teagle Страницы: 40
Eaton APS6-400 Series Installation And Operation Manual preview
APS6-400 Series
Бренд: Eaton Страницы: 114
Dantel 46020-38 Installation & Operation Manual preview
46020-38
Бренд: Dantel Страницы: 62
Bose PowerMatch ESPLink Quick Start Manual preview
PowerMatch ESPLink
Бренд: Bose Страницы: 2
e-con Systems See3CAM 30 Z10X Application User'S Manual preview
See3CAM 30 Z10X
Бренд: e-con Systems Страницы: 14
Buffalo AirStation G54 WLA2-G54 Quick Setup Manual preview
AirStation G54 WLA2-G54
Бренд: Buffalo Страницы: 8
Ricoh Network Scanning Unit A Operating Instructions Manual preview
Network Scanning Unit A
Бренд: Ricoh Страницы: 206
Xcellon DRD-501 User Manual preview
DRD-501
Бренд: Xcellon Страницы: 24
ALIBI ALI-NVR71128R User Manual preview
ALI-NVR71128R
Бренд: ALIBI Страницы: 232
ActiveEye K9504L-W Operation Manual preview
K9504L-W
Бренд: ActiveEye Страницы: 35
AMD -K6-2/450 - MHz Processor Application Note preview
-K6-2/450 - MHz Processor
Бренд: AMD Страницы: 98
Allen-Bradley SLC 5/03 Installation Instructions Manual preview
SLC 5/03
Бренд: Allen-Bradley Страницы: 76
Aaeon FWS-7811 Manual preview
FWS-7811
Бренд: Aaeon Страницы: 100
Roland Symphonique Strings SRX-04 Owner'S Manual preview
Symphonique Strings SRX-04
Бренд: Roland Страницы: 12
Me VS-M1 Instructions Manual preview
VS-M1
Бренд: Me Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды