Lucent Technologies DSP1611 Скачать руководство пользователя страница 166 | Manualshive

Страница: 166 / 443

Lucent Technologies DSP1611 Скачать руководство пользователя страница 166

Information Manual

DSP1611/17/18/27/28/29 DIGITAL SIGNAL PROCESSOR

April 1998

Core Architecture

Lucent Technologies Inc.

DRAFT COPY

5-11

5.2 X Address Arithmetic Unit (XAAU)

The X address arithmetic unit (XAAU) is shown in

. It consists of a 16-bit adder; an offset register (i); and

four pointer registers: the program counter (PC

1

), the program return (pr), the program interrupt (pi), and the table

pointer (pt). These registers are used to address the X space memory or instruction/coefficient memory. The i
register is used to postmodify the pt register. The pt, pr, pi, and i registers are user-accessible and can be modi-
fied under program control. All of the registers are 16 bits wide. All contain unsigned data except for i which con-
tains signed data. The X-memory space contains internal ROM, the internal dual-port RAM, and external
memory. The X-memory space is described in

Section 3.2, Memory Space and Addressing

.

5-4158

Figure 5-5. XAAU—X Address Arithmetic Unit

5.2.1 Inputs and Outputs

The outputs of the XAAU are the instruction/coefficient address bus XAB and the memory segment enables (see

Section 5.2.2, X-Memory Space Segment Selection

). The internal data bus IDB provides access to all of the regis-

ters except PC.

5.2.2 X-Memory Space Segment Selection

The 64K addresses in the X-memory space are divided into three segments: ROM, RAM, and EROM (see

3.2, Memory Space and Addressing

). These three segments can be arranged four different ways (four different

memory maps) in the space. The XAAU provides enable lines for the three segments. Additionally, the RAM seg-
ment is divided into multiple banks of 1 Kwords each. Each bank has an enable line from the XAAU. The enable
lines are enabled one at a time depending on the address and the memory map.

1.The upper case denotes that this register is not accessible by instructions.

i (16)

1

MUX

ADDER

PC (16)

pt (16)

pi (16)

16

ADDRESS

BUS

16

XAAU

(16)

pr(16)

XAB

IDB

MEMORY

SEGMENT

ENABLES

«
...
164
165
166
167
168
...
»

Содержание DSP1611




























































































































































































































































































































































































































































Отзывы:

Нет отзывов