Lucent Technologies Definity Audix System Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 208

Lucent Technologies Definity Audix System Скачать руководство пользователя страница 46

Hardware Installation

2-24

Issue 2 December 1996

Task 8: Install the Control-Link Cable

This task is required only if the DEFINITY AUDIX system is to be run in the CL
integration mode.

The control-link cable can be connected to the switch in one of the following six
ways:

■

Directly to the processor interface (PI) board

■

Via an IDI to the processor interface (PI) board (TN765)

■

Via an MPDM to the digital-line interface board (TN754)

■

Via an IDI to the packet gateway board (TN577) of a G3r only

■

Via DSUs to the packet gateway board (TN577) of a G3r only

■

Via MPDMs to the packet gateway board (TN577) of a G3r only

Use Worksheet A-4 to determine which of the six cable-connection
configurations to install. Then follow the steps in one of the following four
subsections.

In the steps in the following subsections, the equipment described is
cross-referenced to the circled numbers in the figures.

Connect to the PI without an IDI

!

WARNING:

Electric shock and/or fire may result from a cabinet-to-cabinet connection of
the H600-406 control-link cable. Direct connection of the H600-406
control-link cable is to be used within a single cabinet only.

Refer to Figure 2-11, Connecting the Control Link Cable to the PI without an IDI,
when performing this task.

«
...
44
45
46
47
48
...
»

Содержание Definity Audix System

















































































































































































































Отзывы:

Нет отзывов