macnaught.com
3
Lubemate | Oil Control Gun
INSTRUCTION MANUAL
GENERAL SAFETY REGULATIONS
1. Keep the work area clean and dry. Damp or
wet work areas can result in injury.
2. Keep children away from work area. Do not
allow children to handle this product.
3. Use the right tool for the job. Do not attempt
to force small equipment to do the work of larger
industrial equipment. There are certain applications
for which this equipment was designed. It will
do the job better and more safely at the capacity
for which it was intended. Do not modify this
equipment, and do not use this equipment for
a purpose for which it Was not intended.
4. Check for damaged parts. Before using this
product, carefully check that it will operate
properly and perform its intended function.
Check for damaged parts and any other conditions
that may affect the operation of this product.
Replace damaged or worn parts immediately.
5. Do not overreach. Keep proper footing and
balance at all times to prevent tripping, falling,
back injury, etc.
6. DO NOT use the equipment when tired or under
the influence of drugs, alcohol, or medication.
A moment of inattention while operating this
equipment may result in serious personal injury.
SAFETY PRECAUTIONS
WARNING
Read carefully and understand all INSTRUCTIONS
before operating. Failure to follow the safety
rules and other basic safety precautions may
result in serious personal injury. Save these
instructions in a safe place and on hand so that
they can be read when required. Keep these
instructions to assist in future servicing.
WARNING!
The warnings, cautions, and instructions
discussed in this instruction manual cannot cover
all possible conditions or situations that could
occur. It must be understood by the operator
that common sense and caution are factors that
cannot be built into this product, but must be
supplied by the operator.
INSTALLATION
1. This oil control valve has a 1/2" BSP threaded oil inlet, use Teflon tape or an equivalent oil resistant
thread sealant on all threaded connections.
TROUBLESHOOTING GUIDE
Always turn off and relieve line pressure before carrying out any maintenance or repairs.
Ensure that all equipment in the system are operating properly.
AREA 4:
FOR BATTERY CAPACITY
AREA 2:
FOR MEASUREMENT UNITS
Value
ER14250 3.6V
1-35L/min
0.5-100bar
Data
Flow rate
Operating Pressure Range
60°C
±0.5%
Accuracy
Battery
Max operation temperature
1
2
3
4
5
6
Fig. 2
1. Air supply
2. Shut off air valve
3. Oil Pump
4. Shut off oil valve
5. Hose reel
6. Oil control valve
Display and button usage
Notes: It will flashing when
battery voltage less than 3.3V;
AREA 1:
FOR LAST DISPENSE CYCLE
AREA 3:
FOR ACCUMULATED TOTAL
Menu:
MOVING THE NUMBERS FOR
ADJUSTING THE CALIBRATION
AND CHOOSING THE UNITS
Reset:
CHOOSING THE UNITS AND
SETTING CORRECTION FACTOR
AREA 4:
FOR BATTERY CAPACITY
AREA 2:
FOR MEASUREMENT UNITS
Value
ER14250 3.6V
1-35L/min
0.5-100bar
Data
Flow rate
Operating Pressure Range
60°C
±0.5%
Accuracy
Battery
Max operation temperature
1
2
3
4
5
6
Fig. 2
1. Air supply
2. Shut off air valve
3. Oil Pump
4. Shut off oil valve
5. Hose reel
6. Oil control valve
Display and button usage
Notes: It will flashing when
battery voltage less than 3.3V;
AREA 1:
FOR LAST DISPENSE CYCLE
AREA 3:
FOR ACCUMULATED TOTAL
Menu:
MOVING THE NUMBERS FOR
ADJUSTING THE CALIBRATION
AND CHOOSING THE UNITS
Reset:
CHOOSING THE UNITS AND
SETTING CORRECTION FACTOR
Problem
Cause
Solution
Slow or no
fluid flow
Filter is clogged, or pump pressure is
low, or shut-off valve is not fully open,
or foreign materialis jammed in the
metering element.
1. Relief the pressure.
2. Loose swivel fitting, clean or
replace the filter.
3. If the problem remains,
contact your distributor for
repair or replacement.
Oil leaks
from swivel
Swivel is loose
O-ring is worn or damaged
Torque the swivel.
If the problem remains, contact your
distributor for repair or replacement.
Replace the o-ring.
If the problem remains, contact your
distributor for repair or replacement.
Oil drips
from nozzle
Nozzle is damaged or obstructed
Inspect the nozzle for damage or
obstructions, and replace if damaged
If the problem remains, contact your
distributor for repair or replacement.
Valve leaks
O-rings or valve seat are worn or
damaged
Replace the o-rings and/or the
valve seat. If the problem remains,
contact your distributor for repair
or replacement.
No spare parts available.
MAC0619_Lubemate_InstructionManual_L-OCGAE-L-OCGME_D2.indd 3-4
7/8/18 4:46 pm
