200E-A
Seite 2 von 3
www.LSL.eu
Dimensions:
Length: A1 = 60, A2 = 87, A3 = 102 mm
Height: B1 = 68, B2 = 72, B3 = 74 mm
Dimensions are without clamps.
Mounting and safety instructions
LSL Headlight Bracket – Adjustable width
Thank you for buying a LSL product. Because of our passion for motorcycles all our products are designed to meet your needs as a motorcyclist. We wish you always a safe and pleasant ride with your new LSL product from Paaschburg
& Wunderlich GmbH.
Please read this manual carefully prior to installation.
ATTENTION:
Important safety instructions. The assembly of the fork components is a safety-relevant work on the vehicle. If you are not a trained mechanic, contact a specialist workshop to install the levers. Please follow the installation
procedure to the specifications of the vehicle manufacturer. Failure to follow the installation instructions may cause damage to your vehicle and will void the warranty. For consequential damages no liability is assumed. Improper use
of this product may affect riding safety. Structural changes to the parts are to be omitted and lead to the loss of liability and warranty claims.
Please keep this manual for later use.
ATTENTION:
Please note that LSL lamp holders are not tested or approved for use with other accessories such as lamp covers. The combination can lead to impairment of the functioning of the product.
Parts List:
1 set of LSL stanchion clamps (4 pcs.)
1 pair of LSL head light braces (2 pcs.)
Mounting the LSL lamp holder:
1.
Place your vehicle on the main stand or a suitable stand. Relieve the front wheel and make sure that the bike is stable even after releasing the weight.
2.
Remove the wiring from the original headlight and disconnect the headlight from the original lamp holders.
3.
Remove any existing equipment from the upper triple clamp. Disassemble the upper fork bridge and remove the original lamp holder from the two standpipes.
4.
Slide two lamp retaining clips on each of the fork tubes. Position the clamps so the screws point outwards.
5.
Place the lamp braces between the two lamp retaining clips and screw them together from above or below, using the hexagon socket screws M6x20.
6.
Now place the headlamp between the two retaining struts and screw it with the original screws of the headlamp. So that the headlamp sits exactly in the center, the holding clamps must be screwed in on both sides at the same
angle to the headlamp. In this position, tighten the axially seated M6x20 screws.
7.
Now you can move the headlight to the correct height and then tighten the clamping screws of the retaining clips.
8.
Make sure that the headlamp is pointing straight ahead after installation and that the light cone illuminates the road at the correct height. Check that the front fork can be moved freely and that neither the headlamp, nor its wiring,
or the bracket itself hits the frame when in full lock.
9.
When adjusting the headlamp, follow the instructions of the vehicle manufacturer. Finally make sure that all scews have been tightend properly.
Before each ride:
It is the duty and responsibility of the rider to regularly check and maintain the safety-related vehicle parts. Before starting your journey, check the correct adjustment and function of headlight and mounting and the tightness of all
screwed connections.
Warranty:
Take the time to do a 100% professional job of mounting this LSL headlight bracket. Please take into account all our installation and safety instructions.
A faulty, improper installation or handling of the product will void the warranty.
Maintenance/Care:
Do not use aggressive detergents to care for the LSL headlight brackets. The parts can be perfectly cleaned with a simple, lukewarm detergent solution. Contact with brake fluid, brake cleaner, fuel, etc. should be avoided.
Immediately pick up any unintentionally applied impurities with a soft cloth and clean the surface with detergent solution
Enviromental Information:
This product may not be disposed in the normal household rubbish at the end of its lifetime.
The disposal can be done through the Paaschburg u. Wunderlich customer service or a local return and waste collection institution.
Find suitable housings, turn signals, taillights, power resistors, electronic flasher relays, adapter cables and other accessories in our Webshop!
Exclusion of liability and guarantee regulation:
In case of inappropriate use or installation of the device, all guarantee claims and liability for direct or indirect or subsequent damage become invalid. Paaschburg & Wunderlich GmbH is not liable for any damage resulting usage, installation or connecting of the device. In particular the liability on damage to person and financial
loss is excluded. The use of the device in public traffic is at owner’s risk solely.
Paaschburg & Wunderlich GmbH, Am Alten Lokschuppen 10a, D-21509 Glinde
Tel.: +49 (0) 40 248 277-0; E-Mail:
All rights reserved. Changes and errors are excepted.
143LA-A_Rev00_2019-10
1, 2, 3
1, 2, 3
Mounting example for the lamp holder 1, 2, 3
