background image

Status LED

Function key

Relay operation 
status indication 
lamp

Direction key

Remote /
Local

CB
CLOSE/OPEN

MMI structure

How to operate CB Close/Open

Go to SYSTEM CONFIG menu on the initial screen.

Then go to RELAY CONFIG menu in the SYSTEM CONFIG.

Generate a cursor, and put the value to where you want to input.

The confirmation for the setting values can be done by following 

~

process.

(After confirm, press         to go back to the initial screen.)

* When it is not operated for 15

minutes while the password has
been released, the lamp on the LCD
screen will be off and it will be locked
again (But checking correction
value/measurement value is still
available regardless of the password)

* When approving the DC power again

after turn it off, it requires the
password input.

X 1 times

X 3 times

(Switch to Local(In site operation) status 

and confirm)

(Indicated approximately for 3~4 sec)

Close

Open

Close

Open

Operation

1) It works by pressing the Close / Open

button of the relay twice.

2) 

operation should be conducted while

the 

is indicated on the indication screen.

3) When the password is released, 

② , ③

processes will be skipped and Close /
Open operation will be conducted through

① , ④

and 

processes.

4) The password is required only when

inputting correction values, conducting
controls, and rebooting.

Checking status and measurement value monitoring
will be still available without password. 

Function key

Direction key

Status LED

Operation Power
status indication
: Lights up when

operation power is
approved.

Indicates communication
status with
monitoring department
: Flickering when

sending/receiving data

Indicates abnormal
status by internal
selfdiagnosis
: Lights up when an

error occurs

Indicates operation
status of the relay
: Flickering in Pick-up

status Lights up in
Trip status

CT/PT input

When input is over, save the changed 
value by pressing          , and then press 
        to go back to the preveious screen 
(             ).

(Initial monitor)

X 4 times

Press          
to generate 
a cursor.

Change the 
value by using

and move
the cursor with

,

.

Put     in the [  ] 
by using

and move
the cursor with

,

.

5-1

: Display simple single line

diagram and measurement value

: Confirmation button, back to

the detail settings

: Cancel button, back to the

previous screen

: Cursor movement button

: Change the correction 

values or relay elements. (    )

: Set the relay operation status

indication lamp

: Relay Reset button

: Save settings

: Delete accumulation

value (Wh, Vo, Io,
Event/Fault History)

Содержание GIPAM 2000







Отзывы: