LS tractor J2023H Скачать руководство пользователя страница 85

Страница: 85 / 113

5 - 12

(11) Adjustment of Brake pedal play

Check the distance of brake pedal play.

Normal distance : 100~110mm (3.9~4.3 in)

If the distance is more than 110mm (4.3 in),

adjust it as below.

1. Loosen locking nut of the left side first and turn

brake rod to adjust.

2. If brake rod is tightened, the distance shall be

reduced, and if brake rod is loosened, the

distance shall be increased.

3. After adjusting distance, tighten the locking nut.

4. Adjust the brake rod of the right side as the same

way.

5. Check if the brake distance is normal as below.

Left/ Right brake distance

is different.

Normal

Checking brake distance.

1. Check the skid mark of tire or balance of tractor

while driving at a normal speed.

2. If the brake distance is different as shown in right

figure, adjust the brake rod again.

3. Tighten the brake rod of the opposite side

against the inclination a little until the brake

distance is normal.

Brake pedal

Brake rod

Locking Nut

Содержание J2023H


















































































































Результаты поиска

Содержание J2023H

Отзывы:

Похожие инструкции для J2023H

Бренды по названию

Популярные бренды

LS tractor J2023H, Руководство оператора

Результаты поиска

Содержание J2023H

Отзывы:

Похожие инструкции для J2023H

Бренды по названию

Популярные бренды