LRX RAPTOR Скачать руководство пользователя страница 9

Страница: 9 / 19

LRX™

RAPTOR

www.lrx-lighting.com

Check on line for the latest updates at www.lrx-lighting.com

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

FIXTURE SPECIFCATIONS

Electrical

Control power:



Volts: 120 AC – non dimmed feed line.



Hertz: 50 - 60



Amps: 2.0



Connector: U- Ground plug/Edison plug.

Lamps:



500 & 1,000 Watt par 64 type lamps with a GX16D base



Volts – 120/240 VAC



Hertz – 50/60



Input Connector for lamps: Socapex SL61-19 Contacts/Model:

419AR



Quantity: Three (six lamps per connector/one lamp per circuit)

Data: DMX protocol

Data connector:



XLR type, five pin & five wire



Pin 1 = ground



Pin 2 = Data negative



Pin 3 = Data positive



Pin 4 = 12VDC negative



Pin 5 = 12 VDC positive

Physical:



Tilt: Range one hundred degrees - vertical (Zero degrees) to

negative one hundred and twenty degrees



Pan: 340 degrees



Weight: 170 pounds approximate



Gel frames: 48” X 65”



Fixture mounting hooks have been designed to mate with truss

chords not greater than two inches (50.8mm) in diameter

Содержание RAPTOR




















Результаты поиска

Содержание RAPTOR

Отзывы:

Похожие инструкции для RAPTOR

Бренды по названию

Популярные бренды

LRX RAPTOR, Быстрый старт

Результаты поиска

Содержание RAPTOR

Отзывы:

Похожие инструкции для RAPTOR

Бренды по названию

Популярные бренды