LRP shark 18 ATV, Инструкция по эксплуатации, Страница: 30 / 34

,*ʇ*,", Ê{7Ê / , Ê , Ê / 6 ,*ʇ*,", Ê{7Ê / , Ê , Ê / 6
30 30
t
LRP electronic GmbH
Wilhelm-Enssle-Str. 132-134
73630 Remshalden
Germany
info@LRP.cc
www.LRP.cc
USER GUIDE
• IMPORTANT: Never leave your RC model unsupervised when the
battery is plugged in. If a defect occurs, it could set fire to the
model or the surroundings.
• Never wrap your speed-control in plastic film or metal foil. In fact,
make sure it gets enough fresh air.
IMPORTANT: Pay close attention to the following points, as they
will destroy the speed-control and void your warranty:
• Never solder a Schottky diode to the motor when you are using
an LRP A.I.Runner/Runner-Plus (or LRP A.I.Micro) speed-
control. A Schottky diode will destroy any forward/reverse
speed-control.
• Never allow the output stages (FETs) to touch a metal surface
- short-circuit hazard.
• Never cut off the original power plug.
• If the speed-control is connected to the motor, never run the mo-
tor directly with a separate battery or run-in device.
• Never connect the speed-control incorrectly or with reversed
polarity.
• All wires and connections have to be well insulated. Short-cir-
cuits will destroy the speed-control. Pay special attention to the
receiver- and switch wires.
• Never change the polarity of the receiver connector.
• Never open the speed-control and never solder on the PCB.
WARNING NOTES
SPECIFICATION
• Affix the speed-control using the supplied doubled-sided adhesive tape.
• Make sure there are enough cooling slits in the body. This will increase the performance and
life of all the electronic components.
• Position the speed-control where it is protected in the event of a crash.
• Install the speed-control so that you have easy access to the plugs.
• Make sure there is enough clearance (about 3cm) between the speed-control, power cable
and antenna receiver. Avoid any direct contact between power components, the receiver or
the antenna. This can cause interference. If interference occurs, position the components at
a different place in the model.
• The aerial should be run vertically up and away from the receiver. Avoid contact with any
parts made of carbon fibre or metal. If the aerial is too long, don’t coil up the excess length.
It is better to cut it down to a length of about 35 cm. See also the instructions supplied with
your radio control system.
INSTALLATION TIPS
CONNECTIONS
RECEIVER CONNECTING WIRE:
This LRP speed-control is equipped with a LRP Multicon receiver wire. As supplied, it will easily
fit in all ordinary receivers.
WATERPROOF
• Due to latest production technologies and use of HighTech materials, it was possible to make
these speed-controls fully waterproof! This material also makes the speed-controls more
shock resistant then other similar products.
• It‘s no longer needed to seal your speed-control when you are driving in the rain/snow! But
please make sure you still seal your other electronic components (receiver and servo) since
these are normally not waterproof.
INSTALLATION
• Solder the capacitors to the motor.
• Attach the speed-control to the model.
• Connect the speed-control to the receiver (Position: channel 2).
• Connect the speed-control to the motor, using the blue (-) and yellow (+) wires (only yellow
connector on A.I.Micro Reverse!).
• Then check all connections before connecting the speed-control to a battery.
CAUTION : If a connection is incorrect, it will destroy the speed-control.
• The speed-control is now ready to start.
* Transistors rating at 25°C junction temperature. Specifications subject to change without notice.
** @6cells (7,2V). using single motor
*** @6cells (7.2V) using micro motor.
Dear Customer,
thank you for your trust in this LRP product. By purchasing an LRP A.I.Runner/Runner-Plus (or
LRP A.I.Micro) Reverse digital speed-control, you have chosen a high-performance speed-cont-
rol full of new design features, such as:
• Fully waterproof and shock-resistant • LRP A.I. Automatic Setup
• Multi-Protection System • Fail Safe System
Please read and understand these instructions completely before you use this product!
With operating this product, you accept the LRP warranty terms.
Product A.I.Micro A.I.Runner A.I.Runner-Plus
Order No. 83045 83010 83060
Forward/Brake/Reverse yes yes yes
Case Size 26.0x26.0x15.7mm 26.0x26.0x15.7mm 26.0x26.0x15.7mm
Weight (excl. wires) 19.0g 19.0g 19.0g
Voltage Input 4-6 cells (4.8-7.2V) 4-6 cells (4.8-7.2V) 4-6 cells (4.8-7.2V)
Typical Voltage Drop* 0.160V@10A 0.320V@20A 0.144V@20A
Rated Current* 60A 60A 75A
Rec. Motor Limit No Motorlimit*** Over 18Turn** Over 15Turn**
B.E.C. 5.0V 5.0V 5.0 V
High Frequency yes yes yes
Fail-Safe-System yes yes yes
Multi-Protection-System yes yes yes
Connectors Standard Micro Style Standard Tamiya Style Standard Tamiya Style
Setup Procedure Automatic Automatic Automatic
ORDER NO,:
83045
F REVERSE
NO MOTORLIMIT
(WITH MICROSIZE MOTORS)
F REVERSE
OVER 18 TURNS
60 AMPS
F REVERSE
OVER 15 TURNS
75 AMPS
A.I.MICRO Reverse (#83045): ( ) .
IMPORTANT (A.I.Runner and Runner-Plus only!): ( y ) .
• The supplied heatsink is important and improves the per-
formance of your speed-control when used close to its
specified limits. Use only genuine LRP A.I.Runner series
heatsinks. Never allow the Fet tabs to touch other Fets,
short circuit would occur!
• The LRP A.I.Micro Reverse doesn‘t come with a heatsink
and doesn‘t require a heatsink either!
RA00166
ORDER NO,:
83010
ORDER NO,:
83060
A.I.RUNNER Reverse (#83010) ( )
A.I.RUNNER-PLUS Reverse (#83060) ( )
Yellow
T
Motor Connector
(yellow = plus) (blue = minus)
Red Co
MOTOR SUPPRESSION
CAUTION: Never use Schottky diodes in
conjunction with a forward/reverse speed-
control, e.g. the LRP A.I.Runner/Runner-
Plus (or LRP A.I.Micro) Reverse digital
speed-control.
Motors with no capacitors or not enough
capacitors may interfere with the speed-
control. To avoid this, solder the supplied
capacitors to your motor (see picture).
LRP_Shark-18_ATV_Anleitung_071112_JB.indd 30 LRP_Shark-18_ATV_Anleitung_071112_JB.indd 30 12.11.2007 16:46:34 12.11.2007 16:46:34