LOYTEC L-IP Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 173

LOYTEC L-IP Скачать руководство пользователя страница 41

L-IP User Manual

41

LOYTEC

Version 6.1

LOYTEC electronics GmbH

9 - Bit-rate auto-detection configuration source (only if RS-485 port is present)

This menu item allows to set what decision element should be used to enable or disable the
bit-rate auto-detection. If [1] DIP Switch is selected the value set on the DIP switch (refer to
the installation sheet of the product) is used to enable or disable the bit-rate auto-detection.
If [2] Manual is selected the setting made with Option 1 – 5 is used to enable or disable the
bit-rate auto-detection.

r - Router configuration

This menu item opens the CEA-709 router configuration menu as described in Section
5.5.2.

5.5.2 CEA-709 Router Configuration Menu

This menu allows configuring the CEA-709 router mode.

CEA-709 Router/Switch Menu
==========================

[1] Router mode : Smart Switch
[2] Subnet/node learning : subnet/node
[3] Group learning : enabled
[5] Block unknown domains : disabled
[6] Switch reset w. status button : enabled

[q] Quit without saving
[x] Exit and save

Please choose:

Figure 30 CEA-709 router configuration menu.

1 - Router Mode

The router mode menu allows setting the principal operating mode of the L-IP routing core.
Normally the operating mode of the routing core is set with the DIP switches 1 and 2 but
can be overridden in this menu.

Set router mode
===============

[1] Enable Configured Router Mode
[2] Enable Smart Switch Mode
[3] Set router configuration according to DIP switch

Please choose:

Figure 31 Router mode configuration menu

2 - Subnet/node learning

This menu option allows selecting the subnet/node learning mode (see Figure 32).

Set subnet/node learning mode
=============================

[1] Subnet/node learning
[2] Subnet learning
[3] Disable
[4] Set router configuration according to DIP switch

Please choose:

Figure 32 Selecting subnet/node learning mode

If subnet/node learning is selected the L-IP will learn based on subnet/node addresses (see
Section 7.1.2). Subnet broadcasts are flooded. This mode is plug&play.

If subnet learning is selected the L-IP will learn based on subnets. Subnet broadcasts are
only forwarded to ports, which contain nodes with that subnet. Subnet learning should be

«
...
39
40
41
42
43
...
»

Содержание L-IP














































































































































































Отзывы:

Нет отзывов