LOYTEC L-IP Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 173

LOYTEC L-IP Скачать руководство пользователя страница 31

L-IP User Manual

31

LOYTEC

Version 6.1

LOYTEC electronics GmbH



Clearing the group forwarding, the subnet/node forwarding and the router domain table
when used in smart switch mode.



Setting all ports to unconfigured.



Clearing the L-IP status and statistic data.



But

does not

clear the IP address and CEA-852 configuration settings.

All  this  is  done  when  the  button  is  released.  Afterwards  a  reset  is  performed  to  let  the
changes take effect. Once the button is held down for more than 20 seconds the  CEA-709
activity  and  the  CNIP  LED  are  switched  to  orange  and  stay  orange  until  the  button  is
released and the L-IP is reset. This indicates that the forwarding tables will be reset.

Alternatively to holding down the status button the forwarding tables can be reset by
selecting the menu item “Reset to factory defaults” in the console menu (see Section 5.9).

Important:

If the L-IP is operated in smart switch mode and is moved from one location to another
or if major changes to the configuration of the network are made, it is recommended to
reset the L-IP forwarding tables.

Important:

Wait at least 30 seconds after power-up of the L-IP before pressing the Status Button to
ensure that the L-IP has booted properly!

4.6 LCD Display and Jog Dial

4.6.1 Device Setup

The L-IP series “C” models with an LCD display can also be configured to their basic
settings through jog dial navigation on the LCD UI. The main page of the LCD UI is shown
in Figure 19. It displays the device’s IP address, hostname, CPU load, system temperature
and supply voltage. On devices that don’t have Ethernet link LEDs, the LCD display shows
the link status as

Eth1+2

or a respective combination thereof.

Below are menu items. Turn the jog dial to navigate between menu items and press to enter
a menu or go into selection mode. When in selection mode turn the jog dial to alter the
value and press again to quit the selection.

Figure 19: Main Screen of the LCD UI.

The

Device Settings »»

menu allows configuring basic device settings. Navigate to the

Device Management »»

sub-menu, which is displayed in Figure 20.

Figure 20: Device Management Menu on the LCD UI.

This menu gives you the following options for basic device configuration:

«
...
29
30
31
32
33
...
»

Содержание L-IP














































































































































































Отзывы:

Нет отзывов