manualshive.com logo in svg

LOYTEC L-IP, Руководства пользователя, Страница: 28 / 173

Поделиться
Скачать
LOYTEC L-IP Скачать руководство пользователя страница 28

L-IP User Manual 

28 

LOYTEC 

Version 6.1 

LOYTEC electronics GmbH 

 

4.3  Mounting 

The  device  comes  prepared  for  mounting  on  DIN  rails  following  DIN  EN  50  022.  The 
device can be mounted in any position. However, an installation place with proper airflow 
must be selected to ensure that the L-IP temperature does not exceed the specified range. 

4.4  LED signals 

Available  LEDs  and  their  location  on  the  respective  device  model  can  be  found  on  the 
product’s installation sheet. The installation sheet can be found in the product’s box. 

4.4.1  Power LED 

The power LED lights up green when power is supplied to the power terminals. 

4.4.2  Status LED 

The L-IP is equipped with a red status LED (see installation sheet). This LED is normally 
off. If the fall-back image is executed the status LED flashes red once every second. 

4.4.3  CEA-709 Activity LED 

The  CEA-709  port  on  the  L-IP  has  a  three  color  LED  (green,  red  and  orange,  see 
installation sheet). Table 2 shows different LED patterns of the port and their meaning. 

Behavior 

Description 

Comment 

GREEN flashing fast 

Traffic 

 

GREEN flashing at 1Hz 

Port unconfigured 

Only if L-IP operated as configured 
CEA-709 router (see Section 7.1.1) 

RED permanent 

Port damaged 

 

RED flashing fast 

Traffic with high amount of errors 
L-IP redundant: Loop open 
(see Section 4.4.10) 

 

RED flashing at 1 Hz 
(all ports) 

Firmware image corrupt 
Please upload new firmware 

 

ORANGE permanent 

Port disabled 

e.g. using LSD Tool 
(see Chapter 14) 

ORANGE flashing fast 

Traffic on port configured as management port 

e.g. using LSD Tool 
(see Chapter 14) 

ORANGE flashing at 1 Hz 

Bit-rate auto-detection 

RS-485 ports only 

ORANGE permanent 
(all ports) 

Status button pressed for more than 20 
seconds 
L-IP forwarding tables will be reset once 
button is released 

 

Table 2: CEA-709 Activity LED patterns. 

4.4.4  Twin Router Status LED (L-IP Redundant only) 

The  L-IP  Redundant  has  a  three  color  LED  (green,  red  and  orange,  see  installation sheet) 
showing the twin router status of the device. This LED is labeled “PRIM”.  Table 3 shows 
different LED patterns and their meaning. 

Содержание L-IP














































































































































































Отзывы:

Нет отзывов