manualshive.com logo in svg

LOYTEC L-IP, Руководства пользователя, Страница: 161 / 173

Поделиться
Скачать
LOYTEC L-IP Скачать руководство пользователя страница 161

L-IP User Manual 

161 

LOYTEC 

Version 6.1 

LOYTEC electronics GmbH 

 

or 

LOYTEC Asia Corporation Ltd. 

 

16F.-3, No. 155, Zhongyang Rd 

 

Xindian District 

 

New Taipei City 23150 

 

Taiwan 

email: 

[email protected]   

tel: 

+886 (2) 8913 7838 

 

fax: 

+886 (2) 8913 7830 

13.9 Packet Capture 

13.9.1 Configure Remote Packet Capture 

Remote packet capture is able to capture packets on the Ethernet port. To enable the remote 
packet  capture  feature,  go  to  the 

Ethernet

  port  configuration  and  enable 

Remote  packet 

capture

 as shown in Figure 153.

 

 

Figure 153: Remote packet capture port configuration. 

The default 

Port

 setting may be changed to the desired port. Normally, this can be left at its 

default.  If 

No  authentication

  is  selected,  the  device  will  allow  incoming  capture 

connections  without  requiring  any  credentials.  If 

Username  and  Password

  is  selected  as 

authentication  method,  the  client  Wireshark  will  be  required  to  provide  valid  credentials 
before the capture session can be started. Note, that only the users 

admin

 and 

operator

 are 

allowed to connect if this authentication method is selected. 

Click the 

Save Settings

 button to save the configuration. The changes take effect and do not 

require  to  reboot  the  device.  The  remote  capture  can  also  be  disabled  again  without  a 
reboot. 

13.9.2 Enable Local Capture 

The  device  provides  a  local  capture  feature.  With  local  capture  enabled  the  device  logs 
packets to an internal ring buffer. The log can be downloaded from the Web interface.  To 
verify  that  the  device  is  set  up  correctly,  go  to 

Statistics 

  Packet  capture

  as  shown  in

 

Figure 154

. 

Содержание L-IP














































































































































































Отзывы:

Нет отзывов