LOYTEC L-IP Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 173

LOYTEC L-IP Скачать руководство пользователя страница 147

L-IP User Manual

147

LOYTEC

Version 6.1

LOYTEC electronics GmbH

Figure 141: RS-485 Network Termination.

The  L-IP  supports  bit-rate  auto-detection  on  RS-485  channels.  The  factory  default  DIP-
switch  setting  enables  bit-rate  auto-detection  on  all  RS-485  ports.  Figure  142  shows  the
DIP-switch  settings  to  disable  bit-rate  auto-detection,  assuming  all  other  DIP  switches
remain in the factory default position.

off

on

1 2 3 4 5 6 7

Figure 142: DIP-switch 3 disables bit-rate auto-detection

Alternatively the bit-rate auto-detection can be enabled/disabled via the console menu (see
Section 5.5). Further the console menu allows restarting the bit-rate auto-detection on
selected ports. While the port is auto-detecting the activity LED is flashing orange.

11.4 Redundant Ethernet

11.4.1 Ethernet Cabling Options

The L-IP series “C”  models are equipped with two Ethernet ports, which are connected to
an  internal  Ethernet  switch.  This  allows  for  advanced  cabling  options  to  reduce  cabling
costs  or  to  increase  network  resilience.  For  this  discussion,  the  term

upstream

is used to

designate the direction towards the network, which the devices are connected to. Likewise,
the term

downstream

is used to designate devices more distant to the network which the

devices are connected to.

«
...
145
146
147
148
149
...
»

Содержание L-IP














































































































































































Отзывы:

Нет отзывов