LOYTEC L-Gate Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 113

LOYTEC L-Gate Скачать руководство пользователя страница 65

L-INX/L-GATE User Manual

65

LOYTEC

LOYTEC electronics GmbH

6.4.4 MSTP Activity LED

The MS/TP port has a three-color MSTP Activity LED (see product installation sheet). Table
5 shows the different LED patterns of the port and their meaning. A permanent color reflects
a state. Flicker is for 25 ms when there is activity on the MS/TP data link layer.

Behavior

Description

Comment

GREEN permanently,
flicker off

Multi-Master, token ok, flicker when traffic

Normal condition on a multi-master
MS/TP network.

ORANGE flicker

Sole master, flicker when traffic

Normal condition on a single-master
MS/TP network.

RED permanent, flicker
GREEN

Token lost state, flicker when transmit
attempt

Cable might be broken.

RED flash fast

Transmission or receive errors

This indicates bad cabling.

Table 5: MS/TP Activity LED Patterns.

6.4.5 Modbus LED

The Modbus LED is a three-color LED. Table 6 shows the different LED patterns of the port
and their meaning. Flicker is for 25 ms when there is activity on the bus.

Behavior

Description

Comment

GREEN flicker

Traffic, transmission successful

Normal condition.

RED flicker

Traffic, transmission unsusccesful

Device not responding or other
network error.

Table 6: Modbus Activity LED Patterns.

6.4.6 EXT LED

The EXT port has a three-color LED (see product installation sheet), which displays link and
traffic information on the protocol enabled on the port (M-Bus or KNX TP1). Table 7 shows
the different LED patterns of the port and their meaning. A permanent color reflects a state.
Flicker is for 25 ms when there is activity on the attached network. The LGATE-951/952 and
the LINX-153 have more than one EXT port that all conform to the described behavior.

Behavior

Description

Comment

GREEN permanently,
flicker off

LKNX-300 attached, flicker when traffic

Normal condition on a KNX TP1
network.

GREEN flash fast

M-Bus traffic

Normal condition on an M-Bus
network.

RED permanent

LKNX-300 not attached, no KNX bus
power or port damaged

Check if cabling to LKNX-300 is
bad.

RED flash fast

M-Bus transmission or receive errors

This indicates bad cabling. Check if
L-MBUS is connected. Check if
M-Bus devices are operational.

Table 7: EXT port LED Patterns.

6.4.7 Ethernet Link LED

The Ethernet Link LED lights up green whenever an Ethernet cable is plugged-in and a
physical connection with a switch, hub, or PC can be established.

6.4.8 Ethernet Activity LED

The Ethernet Activity LED lights up green for 6 ms whenever a packet is transmitted or
received or when a collision is detected on the network cable.

«
...
63
64
65
66
67
...
»

Содержание L-Gate


















































































































Отзывы:

Нет отзывов