background image

StructureScan 3D Transducer mounting options

"Transom mount (Transom
bracket)"

 on page 9

Keeps transducer in the water when the
boat is on plane, allowing you to track
bottom at high speeds

Transducer angle can be adjusted so it is
parallel with the water

Transducer more likely to collide with
obstructions in the water and adds drag
to the boat

"Jackplate mount (Transom
bracket)"

 on page 10

Transducer is not in the water when boat
is on plane; protects transducer and
prevents drag from transducer

Transducer angle can be adjusted so it is
parallel with the water

Allows you to mount transducer without
drilling holes in your boat

Sonar does not track bottom when
transducer comes out of the water

"Step mount (Transom
bracket)"

 on page 12

Transducer is not in the water when boat
is on plane; protects transducer and
prevents drag from transducer

Transducer angle can be adjusted so it is
parallel with the water

Sonar does not track bottom when
transducer comes out of the water

"Direct Step mount (Flush
bracket)"

 on page 13

Transducer is not in the water when boat
is on plane; protects transducer and
prevents drag from transducer

Transducer angle cannot be adjusted so
it is parallel with the water

Sonar does not track bottom when
transducer comes out of the water

Transom mount bracket assembly

The transom mount bracket assembly comes with four washers, two
bolts and two nuts.

6

Installation

 | StructureScan 3D Transducer

Содержание StructureScan 3D





















Отзывы: