www.lorextechnology.com
LW2310 Series Quick Start Guide_R1
Page 1
This ultra digital wireless video
recording system comes with the
following components:
• Wireless Receiver
• Color Outdoor
Night Vision
Camera*
• Camera Stand*
• SD Memory Card*
• Audio/Video Cable
• Remote Control
• Wall Mounting Kits*
• Wireless Antennas (for receiver
and camera)*
• Power Adapters (for receiver
and camera)*
• IR Extender
• Instruction Manual
B.
Connect the Receiver to a TV/Monitor
1
Connect the Black cable from
the AV cable to AV Out port on
the left panel of the receiver.
Connect the Yellow video cable
and White audio cable (mono)
to your TV or monitor.
Insert the included SD
card into the SD Card
slot on the right panel
of the receiver until you
hear a “click.” Place the
receiver in a place that
will have clear reception
to your camera.
NOTE:
The receiver is
compatible with most major
brands of SD cards up to 16 GB.
NOTE:
Change the video input on your TV or
monitor to the corresponding input of the video
cable (i.e. Video 1, Video 2, Auxiliary, etc.).
NOTE:
IR extender box needs
to have direct line-of-sight with
remote control.
2
OPTIONAL
y
(
,
,
y,
)
OPTIONAL
Connect the included IR
extender to the IR Extend
port on the right panel
of the receiver. Use the IR
extender if you want to
hide the receiver from plain
sight. Place the IR Extender
for example in a bookcase
or above a cabinet and still
fully control the system using
the included remote control.
Connect one end of the
Receiver Power Adaptor to
the receiver and the other
end to an electrical outlet.
The receiver will power on
automatically.
Connect the wireless
antenna to the
receiver, as shown.
4
3
ATTENTION:
Make sure to first con-
nect and power on the camera before
powering on the receiver; this will
ensure a proper connection.
Getting Started
WIRELESS VIDEO MONITORING SYSTEM
LW2310 SERIES
QUICK START GUIDE
*
Number of cameras and SD card
capacity may vary by model. Check your
package for specific content information.
*
NOTE: AVOID INSTALLING IN A LOCATION WHICH REQUIRES THE
WIRELESS SIGNAL TO PASS THROUGH CEMENT, CONCRETE AND METAL
STRUCTURES. THIS WILL REDUCE THE TRANSMISSION RANGE.
Time
Tools
Skills - Easy
Under 20 Minutes*
Hand Tools
Plug & Play connections,
On screen set up
* Installation time may vary
based on application and
camera location
SIMPLY AWARE
™
h
/
Mount camera stand to
the wall.
NOTE:
Wireless cameras require a power source to operate.
NOTE:
Before you install a camera, carefully plan where
and how it will be positioned, and where you will route
the cable that connects the camera to the power adaptor.
Before starting permanent installation, verify its performance
by observing the image on a monitor when the camera is
positioned where it will be permanently installed. Cameras
are rated for indoor/outdoor installation. Not intended for
direct exposure to rain or snow. For outdoor applications
install under shelter protected from the elements
A.
Camera Setup
Connect power adaptor to local
120V AC power outlet.
IMPORTANT:
The motion detection
range is up to 21ft (6.5m) to minimize
false alarms. Keep this in mind when
selecting suitable installation location.
4
Connect one end of the camera
Power Adapter to the camera and the
other end to an electrical outlet.
3
Secure Camera to the mounting stand.
Adjust the angle of the camera until the
desired view is set.
Tighten the thumbscrews to secure the
desired camera position.
1
Attach the included
antenna to the camera by
screwing it on to the side
as shown below.
2
NOTE:
When adding cameras that were not included in the original
box, you will need to pair up the camera with the receiver. Please
refer to the camera pairing section of the User Manual.
NOTE:
This camera includes an Auto Mechanical IR Cut Filter.
When the camera changes between day/night lighting, an audible
clicking noise may be heard coming from the camera. This clicking is
normal, and indicates that the camera filter is working.
PIR motion sensor
osition.
NOTE:
Wireless cameras r
where
as shown below.
NOTE:
If one or more of the cameras do not appear when selected (i.e. Camera 2 is turned on but does not appear on channel 2),
follow the pairing process as described in user manual.
