background image

19

9. Warranty conditions

For the fog machine 

Cryo-Fog

 Look‘ guarantee is:

1. Free of charge, subject to the following conditions (No. 2 - 6) we will repair any defect or

fault in the unit if it is caused by a proven factory fault and has been advised immediately
after appearance and within 12 months of delivery to the end user. Insignificant deviations
of the regular production quality does not guarantee replacement rights, nor do faults
or defects caused by water, wrong fog fluid, by generally abnormal environment
conditions or Force Majeure.

2. Guarantee Service will be done in the following way: Faulty parts will be repaired or

replaced (our choice) with correct parts. Faulty units have to be brought to us or our
service centres or to be sent to us or our service centres at customer‘s expense. The
invoice and/or receipt showing the purchase date and the serial number has to come
with the faulty unit, otherwise this will not be guarantee service. Replaced parts become
our property.

3. The customer loses all rights for guarantee services, if any repairs or adjustments are

done to the units by unauthorized persons and/or if spare parts are used which are not
approved by us. The right of guarantee service is also lost if fluids other than the
authorized original Look fluids have been used or if units are sent to us with full fluid
bottles. Also non compliance with the instructions in this manual or mistakes by incorrect
handling/treating of the machine will lead to a loss of guarantee and also any faults and
damages caused by undue force.

4. Any freight costs arrising in connection with the guarantee services have to be born by

the customer.

5. Guarantee services do not cause an extension of the guarantee time or the start of a

new guarantee time. The warranty for replaced parts ends with the guarantee time of
the whole unit.

6. We may, at our option, replace the machine rather than repair it.

7. Further claims, especially for damages, losses etc. outside the unit are excluded.

Other guarantee regulations may be valid outside the USA. Please check with your dealer!

If you should send the unit for service, do not forget to remove any liquid from the fluid
bottle.

For warranty service in North America contact:

Look Solutions USA Ltd.
1-800-426-4189
[email protected]

Содержание Cryo-Fog





















Отзывы: