LONCIN LC3500i Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 61

LONCIN LC3500i Скачать руководство пользователя страница 33

Chapter IV Disassembly & Repair

- 28 -

4-4-2 Cylinder head/valve

a. Disassembly/assembly

Double-end bolt

(exhaust)

Double-end bolt
(inlet)

Air guide sleeve

Assembly/disassembly:
Unscrew and screw bolt in the
manner of cross.
Torque value: 8-12 N·m

Bolt M6 × 14 (4)

Torque value: (32 ~ 35) N•m
Assembly/disassembly:
Unscrew and screw bolt in the
manner of cross.

Assembly:
Prior to assembly, clear away the carbon
deposition  in  combustor  and  check  the
seal  status  of  valve  seat  then  conduct
assembly.
Measure  the  pressure  of  cylinder  head
after completing assembly.

Cylinder-head bolt: M8 × 60 (4)

Cylinder head

Cylinder-head
sealing gasket

Assembly:
Clean and adjust the spark
plug prior to assembly.
Torque value: 25-28 N·m

Spark plug

Cylinder-head cover

Cylinder-head
cover

Filter

Gasket

Breather pipe

Assembly/disassembly:
Make  one  end  connect
cylinder-head  cover  and
the  other  end  connecting
the

breather

mouth

vertical to breather slot
cover plate.

«
...
31
32
33
34
35
...
»

Содержание LC3500i






























































Отзывы:

Нет отзывов